Panasonic RCCD350 - Manual (Page 6)

6
R
Q
T7
607
6
• If the unit is not used for a long period of time, remove the
batteries to prevent potential damage due to possible battery
leakage.
• Do not heat, disassemble, or allow contact with flame or water.
• Do not peel off the covering and do not use if the covering has been
peeled off.
Battery mishandling can cause electrolyte leakage which can damage
items the fluid contacts and may cause a fire.
If electrolyte leaks from the batteries, consult your dealer.
Wash thoroughly with water if electrolyte comes in contact with any part of
your body.
• Do not use irregularly shaped CDs.
• Do not use non-specification discs.
• Do not use CDs printed with label printers available on the market.
• Do not use CDs with labels and stickers that are coming off or with
adhesive exuding from under labels and stickers.
Note on CD-R/RW
This unit can play CD-R and CD-RW recorded with CD-DA. Use an audio
recording disc and finalize* it when you finish recording. The unit may not
be able to play some discs due to the condition of the recording.
* A process that enables CD-R/CD-RW players to play audio CD-R and
CD-RW.
Note
Specifications are subject to change without notice.
Mass and dimensions are approximate.
To clean this unit, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this unit.
• Before using chemically treated cloth, read the instructions that came
with the cloth carefully.
Cautions
Batteries
CDs
Troubleshooting guide
Before requesting service, make the below checks. If you are in doubt
about some of the check points, or if the remedies indicated in the chart
do not solve the problem, consult your dealer for instructions.
The clock shows
“-:--”. • Set the clock.
There is a lot of
noise. • Keep away from mobile phones,
televisions, and other tuners.
• Extend and change the direction of the
antenna.
The alarm doesn’t
sound at the set time. • Ensure the alarm’s indicator is on (“ALARM 1”,
“ALARM 2”, or “ALARM 3”).
The memory has
been cleared. • Reset the items into the memory.
• Insert a battery to preserve the memory
contents.
“no dISC” appears. • You haven’t inserted a CD.
Play doesn’t start or
display is incorrect. • Clean the CD.
• Clean the lens with a blower (SZZP1038C
recommended). If the lens gets marked
with fingerprints, gently wipe them off with
a cotton swab.
• Wait an hour for condensation to dry, then
try again.
• Make sure the label is facing out.
• Replace the CD if it is scratched, warped,
or irregularly shaped.
The CD or radio
display disappears. • These displays disappear after a few
seconds. To show them again, press
[DISPLAY, –DIMMER].
Specifications
Frequency range
FM:
AM:
Sampling frequency
Decoding
Beam source
(NORSK)
Bølgelengde
Laserstyrke
Number of channels
Wow and flutter
D/A converter
Speakers
Power requirement
Memory back-up
Dimensions (W x H x D)
Mass
87.5 to 108.0 MHz (50 kHz step)
522 to 1629 kHz (9 kHz step)
44.1 kHz
16 bit linear
Semiconductor laser (wavelength 780 nm)
780 nm
Ingen farlig stråling sendes ut
(med sikkerhets-beskyttelse)
2 channel, stereo
Less than possible measurement data
1 bit DAC
4.5 cm, 6 Ω x 2
AC 230 V, 50 Hz
Power consumption: 11 W
9 V (One 6F22/6LR61, 006P battery)
266 x 149 x 137 mm
1.43 kg without battery
Maintenance
Power consumption in standby mode: 2.3 W