Panasonic SCAKX12EG - Manual (Page 8)

RQTX1290
8
8
E
N
G
L
IS
H
ENGL
ISH
Radio
Manual tuning
1 Press [RADIO, EXT-IN] to select “FM” or “AM”.
2 Press [3] or [5] to select the frequency of the required
station.
To tune automatically, press and hold the button until the frequency
starts changing quickly.
To improve the sound quality
When “FM” is selected
1 Press [RADIO MENU] to select “FM MODE”.
2 Press [Y, U] to select “MONO” and then press [OK].
To cancel, select “STEREO”.
• “MONO” is also cancelled when you change the frequency.
• Switch off “MONO” for normal listening.
When “AM” is selected
1 Press [RADIO MENU] to select “B.PROOF”.
2 Press [Y, U] to select “BP 1” or “BP 2” and then press [OK].
Clock and timers
Setting the clock
This is a 24-hour clock.
1 Press [CLOCK/TIMER] to select “CLOCK”.
2 Within 10 seconds, press [R, T] to set the time.
3 Press [OK].
Press [CLOCK/TIMER] to show the clock for a few seconds.
Note:
Reset the clock regularly to maintain accuracy.
RDS broadcasting
This system can display the text data transmitted by the radio data
system (RDS) available in some areas.
Press [ DISPLAY].
Note:
RDS displays may not be available if reception is poor.
Memory presetting
30 FM and 15 AM stations can be preset.
Preparation
Press [RADIO, EXT-IN] to select “FM” or “AM”.
Automatic presetting
1 Press [OK] to select “CURRENT” or “LOWEST” frequency.
2 Press [AUTO PRESET] to start presetting.
To cancel, press [8].
Manual presetting
1 Press [3] or [5] to tune in to the station.
2 Press [PROGRAM].
3 Press the numeric buttons to select a preset number.
The new station replaces any station that occupies the same preset
number.
4 Do steps 1 through 3 again to preset more stations.
Selecting a preset station
Press the numeric buttons, [2] or [6] (main unit: [2/3]
or [5/6]) to select the preset station.
AM allocation setting (by main unit only)
This system can also receive AM broadcasts allocated in 10 kHz steps.
1 Press [RADIO, EXT-IN] to select “FM” or “AM”.
2 Press and hold [RADIO, EXT-IN].
After a few seconds, the display panel shows the current minimum
radio frequency. Release the button when the minimum frequency
changes.
• To go back to the initial setting, do the above steps again.
• After you change the setting, preset frequencies are erased.
PS
(Station name)
→
PTY
(Program type)
→
FREQ
(Frequency)
USB
You can connect and play MP3 tracks from your USB mass storage
device.
Do not use a USB extension cable. The system cannot recognise USB
mass storage device connected through a cable.
1 Decrease the volume and connect the USB mass storage
device to the USB port.
2 Press [USB] and then press [4/9] to start playback.
Stop playback Press [8] during playback.
“RESUME” is shown.
Press [4/9] to continue playback.
OR
Press [8] two times to stop the playback fully.
For other operations, refer to “Discs” (Z 7).
Compatible devices
• USB mass storage devices that support bulk-only transfer.
• USB mass storage devices that support USB 2.0 full speed.
Supported format
• Folders are defined as album.
• Files are defined as track.
• Track must have the extension “.mp3” or “.MP3”.
• CBI (Control/Bulk/Interrupt) is not supported.
• NTFS file system is not supported (only FAT 12/16/32 file system is
supported).
• Some files can fail to work because of the sector size.
Note:
• Maximum album: 255 albums (include albums without MP3 tracks)
• Maximum track: 2500 tracks
• Maximum track in one album: 999 tracks
SC-AKX12_EG_en.indd 8 SC-AKX12_EG_en.indd 8 2/14/2011 10:49:10 AM 2/14/2011 10:49:10 AM