Panasonic SCPT70 - Manual (Page 8)

8
RQ
TX10
24
ENGL
ISH
The Easy setup screen assists you in making necessary
settings.
≥Language
Select the language used on menu screen.
≥TV aspect
Select the aspect to suit your TV.
≥Speakers position
Select “5.1ch layout” mode or “2.1ch layout” mode according to your
speaker layout (B 6, Positioning).
≥Speaker check
Listen to speaker output to confirm speaker connections.
≥Speaker output §
Make surround sound setting for speaker output.
§ Only when “5.1ch layout” mode is selected in “Speakers position”
above.
[Note]
≥ If this unit is connected to a “HDAVI Control 3 or later” compatible TV
via HDMI cable, the menu language and TV aspect information will be
retrieved via VIERA Link.
≥ If this unit is connected to a “HDAVI Control 2” compatible TV via
HDMI cable, the menu language information will be retrieved via
VIERA Link.
≥ Settings in the Easy setup can also be changed in the player settings
[e.g. language, TV aspect (B 15)].
Setting up the radio
Up to 30 stations can be set.
≥ “SET OK” is displayed when the stations are set, and the radio tunes
to the last preset station.
≥ “ERROR” is displayed when automatic presetting is unsuccessful.
Preset the channels manually (B right).
≥ The FM setting is also shown on the TV display.
To cancel the mode, press and hold the button again until “AUTO ST” is
displayed.
≥ The mode is also cancelled when you change the frequency.
Up to 30 stations can be set.
A station previously stored is overwritten when another station is stored
in the same channel preset.
step 5 EASY SETUP
Preparation
Turn on your TV and select the appropriate video input mode (e.g.
VIDEO 1, AV 1, HDMI, etc.) to suit the connections to this unit.
≥ To change your TV’s video input mode, refer to its operating
instructions.
≥ This remote control can perform some basic TV operations (B 4).
1 Press [Í]1 to turn on the unit.
≥ When the Easy setup screen appears automatically, skip step
2 to 6.
2 Press [DVD]@ to select “DVD/CD”.
3 Press [SETUP]; to show the setup menu.
4 Press [3, 4]9 to select “OTHERS” and press [OK]9.
5 Press [3, 4]9 to select “EASY SETUP” and press
[OK]9.
6 Press [OK]9 to select “SET”.
7 Press [3, 4]9 to select “Yes” and press [OK]9.
SET
MAIN
DISC
VIDEO
AUDIO
DISPLAY
HDMI
OTHERS
EXIT : SETUP RETURN
Menu
8 Follow the messages and make the settings with
[3, 4]9 and [OK]9.
(B below, Easy setup settings)
9 Press [OK]9 to finish Easy setup.
Easy setup settings
Presetting stations automatically
1 Press [RADIO]@ to select “FM”.
2 Press [MENU]:.
Each time you press the button:
LOWEST (factory preset):
To begin auto preset with the lowest frequency.
CURRENT:
To begin auto preset with the current frequency.
§
§ To change the frequency, refer to “Manual tuning” (B right).
3 Press and hold [OK]9.
Release the button when “FM AUTO” is displayed.
The tuner starts to preset all the stations it can receive into the
channels in ascending order.
Confirming the preset channels
1 Press [RADIO]@ to select “FM”.
2 Press the numbered buttons to select a channel.
≥ To select a 2-digit number
e.g. 12: [S10]3 B [1] B [2]
Alternatively, press [X, W]6.
If noise is excessive
Press and hold [PLAY MODE]2 to display “MONO”.
Manual tuning
1 Press [RADIO]@ to select “FM”.
2 Press [6, 5]A to select the frequency.
≥ To start automatic tuning, press and hold [6, 5]A until the
frequency starts scrolling. Tuning stops when a station is found.
Presetting stations manually
1 While listening to the radio broadcast
Press [OK]9.
2 While the frequency is flashing on the display
Press the numbered buttons to select a channel.
≥ To select a 2-digit number
e.g. 12: [S10]3 B [1] B [2]
Alternatively, press [X, W]6, and then press [OK]9.
8
SC-PT70EP-RQTX1024-Z_eng.book Page 8 Thursday, August 20, 2009 10:19 AM