Panasonic SCXH10EP - Manual (Page 7)

7
RQ
TX13
09
Getting S
tarted
Quick Start
Gu
ide
E
N
GLIS
H
≥ To listen to the TV audio on the sound system, connect the SCART
cable, optical digital audio cable or audio cable.
Refer to the operating instructions of the respective devices for the
settings necessary to output the audio.
Basic setup example
To improve picture quality, you can change the video signal output from
the SCART (AV) terminal to suit the type of TV you are using.
≥ Select “S-Video”, “RGB 1” or “RGB 2” from “Video Out-SCART” in Video
menu (B 14).
Do not make the video connection through the VCR.
Due to copy guard protection, the picture may not be displayed properly.
[\\\\\\DIGITAL\AUDIO\IN\OPTICAL\\\\\\]
When the optical digital audio cable is connected, this unit can decode
Dolby Digital audio.
Connect the optical digital audio cable (not supplied) from the
DIGITAL AUDIO IN OPTICAL terminal on the main unit to the
OPTICAL OUT terminal on your TV.
After connecting with the optical digital audio cable, make settings to suit
the type of audio from your digital equipment (B 10).
[\\\\\\\\\AUX\\\\\\\\]
Use this connection when the TV does not have an OPTICAL OUT
terminal or when the DIGITAL AUDIO IN OPTICAL terminal on this unit is
being used by the STB.
Connect the audio cable (not supplied) from the AUX terminal on the
main unit to the AUDIO OUT terminal on your TV.
If you have various sound sources (such as Blu-ray Disc player, DVD recorder,
VCR, etc.), connect them to the available inputs on the TV and the TV output
should then be connected to the SCART (AV), AUX or DIGITAL AUDIO IN
OPTICAL terminal of the main unit.
Conserving power
The main unit consumes a small amount of power, even when it is in
standby mode (approx. 0.8 W). To save power when the unit is not to be
used for a long time, unplug it from the household mains socket.
You will need to reset some memory items when plugging back the main
unit.
The supplied AC mains lead is for use with the main unit only.
Do not use it with other equipment. Also, do not use cords for other equipment
with the main unit.
This unit will memorize the playback position when there is a power
failure.
After the power supply recovers, turn on your TV and the main unit.
Playback will resume from the point at which it was stopped.
≥ The resume playback timing may vary a few seconds.
≥ This function may not work for files that do not have resume playback.
≥ The position is cleared if the disc tray is opened or the USB device is
removed.
2 Radio antenna connections
Using an indoor antenna
Using an outdoor antenna
3 Audio and video connections
§ This connection will also enable you to play TV audio through your
home theater system (B 9, Selecting the source using the remote
control). Select the appropriate audio out (e.g. Monitor) on the TV.
FM ANT
(75 )
Adhesive tape
Main unit
(rear)
FM indoor antenna
(supplied)
Affix this end of the antenna
where reception is best.
FM ANT
(75 )
Use outdoor antenna if radio reception is poor.
≥ Disconnect the antenna when the unit is not in use.
≥ Do not use the outdoor antenna during an electrical storm.
Main unit
(rear)
75 ≠ coaxial
cable
(not supplied)
FM outdoor antenna
(Using a TV antenna
(not supplied))
The antenna should be
installed by a competent
technician.
AV
AV AV
SCART cable §
(not supplied)
TV
Main unit (rear)
Other audio connections
step 3 AC mains lead connection
Power failure resume
AC IN
Main unit (rear)
AC mains lead
(supplied)
To household mains socket
7
SC-XH10 EP_RQTX1309-Z_eng.book Page 7 Friday, March 4, 2011 5:55 PM