Panasonic SCAKX52EG - Manual (Page 11)

RQTX1298
11
11
E
N
G
L
IS
H
ENGL
ISH
Deleting the recorded tracks
1 Press [MEMORY, USB] to select “MEMORY” or “USB”.
2 Press [R, T] to select the desired album.
Press [2] or [6] to select the desired track.
3 Press [EDIT MODE] to select the desired mode.
TRACKDEL Delete a single track
ALBUMDEL Delete one album (maximum 999 tracks)
FORMAT Format the USB mass storage device
ALL DEL Delete all albums in the internal memory
4 Press [OK].
The selected item to be deleted is shown.
5 Press [OK].
“SURE?NO” is shown.
6 Press [Y, U] to select “YES” or “NO” and then press [OK].
Select “YES” to confirm the deletion. “WRITING” is shown.
Note on USB
Compatible devices
• USB mass storage devices that support bulk-only transfer.
• USB mass storage devices that support USB 2.0 full speed.
Supported format
• Folders are defined as album.
• Files are defined as track.
• Tracks must have the extension “.mp3” or “.MP3”.
• CBI (Control/Bulk/Interrupt) is not supported.
• NTFS file system is not supported (only FAT 12/16/32 file system is
supported).
• Depending on the sector size, some files can fail to work.
Radio
Manual tuning
1 Press [RADIO, EXT-IN] to select “FM” or “AM”.
2 Press [3] or [5] to select the frequency of the required
station.
To tune automatically, press and hold the button until the frequency
starts changing quickly.
“
” is shown when a stereo FM broadcast is being received.
To improve the sound quality
When “FM” is selected
1 Press [RADIO MENU] to select “FM MODE”.
2 Press [Y, U] to select “MONO” and then press [OK].
To cancel, select “ST”.
• “MONO” is also cancelled when you change the frequency.
• Turn off “MONO” for normal listening.
When “AM” is selected
1 Press [RADIO MENU] to select “B.PROOF”.
2 Press [Y, U] to select “BP 1” or “BP 2” and then press [OK].
RDS broadcasting
This system can show the text data transmitted by the radio data
system (RDS) available in some areas.
Press [ DISPLAY].
Note:
RDS may not be available if reception is poor.
Memory presetting
30 FM and 15 AM stations can be preset.
Preparation
Press [RADIO, EXT-IN] to select “FM” or “AM”.
Automatic presetting
1 Press [OK] to select “LOWEST” or “CURRENT” frequency.
2 Press [RADIO MENU] to select “A.PRESET” and then press
[OK].
“START?” is shown.
3 Press [OK] to start presetting.
Manual presetting
1 Press [3] or [5] to tune in to the station.
2 Press [PROGRAM].
3 Press the alphanumeric buttons to select a preset number.
The new station replaces any station that occupies the same preset
number.
4 Do steps 1 through 3 again to preset more stations.
Selecting a preset station
Press the alphanumeric buttons, [2] or [6] (main unit:
[2/3] or [5/6]) to select the preset station.
AM allocation setting (by main unit only)
This system can also receive AM broadcasts allocated in 10 kHz steps.
1 Press [RADIO, EXT-IN] to select “FM” or “AM”.
2 Press and hold [RADIO, EXT-IN].
After a few seconds, the display panel shows the current minimum
radio frequency. Release the button when the minimum frequency
changes.
• To go back to the initial setting, do the above steps again.
• After you change the setting, preset frequencies are erased.
PS
(Station name)
→
PTY
(Program type)
→
FREQ
(Frequency)
SC-AKX52_EG_en.indd 11 SC-AKX52_EG_en.indd 11 3/4/2011 2:12:54 PM 3/4/2011 2:12:54 PM