Panasonic SCNE3EG - Manual (Page 12)

12
VQT4U54
Sound adjustment
The following sound effects can be added to the audio
output.
1
Press [SOUND] repeatedly to select the effect.
2
Press [3, 4] to select the setting and then press
[OK].
≥ You may experience a reduction in sound quality when these
effects are used with some sources. If this occurs, turn the
sound effects off.
Others
The sleep timer can turn the unit off after a set time.
1
Press [SETUP] to select “SLEEP”.
2
Press [3, 4] to set the time (in minutes) and then
press [OK].
“SLEEP 30” ,. “SLEEP 60” ,. “SLEEP 90” ,. “SLEEP 120”
^---------------------. “OFF” (Cancel) (----------------------J
≥ The remaining time is indicated on the unit’s display except
when other operations are performed.
The brightness of this unit’s display can be changed.
1
Press [SETUP] repeatedly to select “DIMMER”.
2
Press [3, 4] to select “ON” and then press [OK].
≥ To cancel the dimmer, select “OFF” in step 2.
As a factory preset, this unit will always turn off
automatically if there is no sound output and no
operation for approx. 30 minutes.
To cancel this function
1
Press [SETUP] repeatedly to select “AUTO OFF”.
2
Press [3, 4] to select “OFF” and then press [OK].
≥ To turn automatic standby on, select “ON” in step 2.
≥ When connected to a Bluetooth
® device, the automatic
standby function does not work.
To check the Wi-Fi signal strength where the unit is
located.
Preparation
Connect this unit to the wireless network. (l 6)
1
Press [SETUP] repeatedly to select “SIG.LEVEL”
and then press [OK].
≥ The unit’s display shows “LEVEL ”.
(“ ” stands for a number.)
2
Press [OK] to exit this display mode.
≥ It is recommended to have a signal strength of “3”. Change
the position or angle of your wireless network router or the
unit if the indication is “2” or “1” and see if the connection
improves.
≥ If “LEVEL 0” is displayed, this unit cannot establish a link with
the wireless network router. (l 15)
≥ This function does not work when “D.CONNECT” is set to
“ON”.
This unit can turn on automatically from standby mode
when this unit is selected as the AirPlay speakers.
Preparation
Connect this unit to the wireless network. (l 6)
1
Press [SETUP] repeatedly to select “NET STNBY”
and then press [OK].
2
Press [3, 4] to select “ON” and then press [OK].
≥ To cancel this function, select “OFF” in step 2.
≥ The factory preset is “OFF”. If this function is set to “ON” the
standby power consumption will increase.
Direct-Vocal
Surround
(D.SURROUND) “LEVEL 1”, “LEVEL 2” or
“OFF”.
≥ The factory preset is “OFF”.
Preset EQ
(PRESET EQ) “HEAVY” (heavy), “SOFT”
(soft), “CLEAR” (clear),
“VOCAL” (vocal) or “FLAT”
(flat/off).
≥ The factory preset is “HEAVY”.
Bass (BASS) or
Treble (TREBLE) Adjust the level (j4 to i4).
Dynamic Bass
(D.BASS) “ON D.BASS” or
“OFF D.BASS”.
≥ The factory preset is
“ON D.BASS”.
Sleep timer
Display brightness
Automatic standby
Wi-Fi signal strength
Network standby
SC-NE3_EG~VQT4U54.book 12 ページ ２０１３年１月１６日 水曜日 午前９時３分