AeroBed EcoLite - Manual (Page 2)

LIMITED EXPRESS WARRANTY
Aero Products International, Inc. (“us”) warrants to the original purchaser (“you”) that the AeroBed (“product”) is guaranteed against defects
in materials and workmanship for the following periods: pump and valve, two (2) years from date of purchase; mattress, one (1) year from
date of purchase.
Exclusions
Our obligation under this limited express warranty shall not apply if our inspection shows:
A. That the product is used for other than normal indoor sleeping purposes.
B. Any product or part has been damaged by alteration.
C. Any product or part has been subject to accident, misuse, abuse or has been operated contrary to our written instructions.
Warranty Redemptions
You must obtain an authorization from us before returning a defective product. Call us at 1-888-462-4468 or write us at Aero Products International, Inc., 1834 Walden
Office Square, Third Floor, Schaumburg, IL 60173 for a return authorization. The product should be carefully packaged and delivered postage or delivery charges
prepaid at the address set forth above. You are responsible for all damages incurred in shipping.
Warranty Disclaimer
EXCEPT FOR THE LIMITED EXPRESS WARRANTY SET FORTH IN THIS SECTION, OR ANY IMPLIED WARRANTIES PERMITTED UNDER APPLICABLE LAW,
SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATIONS. ALL CLAIMS AGAINST US MUST BE BROUGHT WITHIN ONE (1) YEAR FROM THE TIME
THEY ARISE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE DISCLAIMER MAY NOT APPLY
TO YOU.
Limitation of Liability
TO THE FULLEST EXTENT PERMITTED BY LAW, SELLER SHALL NOT BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
WITH RESPECT TO THE SALE OF USE OF THE PRODUCTS, INCLUDING ANY LOST REVENUES, LOSS OF USE OR LOST PROFITS, REGARDLESS OF THE
THEORY BY WHICH ANY CLAIM MAY BE BASED, INCLUDING ANY TORT, TANGIBLE PROPERTY DAMAGE OR STATUTORY CAUSES OF ACTION. NOTWITH-
STANDING THE TERM OF ANY LIMITED OR IMPLIED WARRANTY, OR IN THE EVENT THAT ANY LIMITED WARRANTY FAILS OF ITS ESSENTIAL PURPOSE, IN
NO EVENT WILL OUR ENTIRE LIABILITY TO YOU EXCEED THE PURCHASE PRICE ACTUALLY PAID BY YOU FOR THE PRODUCTS, OR ANY DEFECTIVE OR
NONCONFORMING PORTION THEREOF, WHICHEVER IS THE LESSER AMOUNT.
THIS LIMITATION DOES NOT APPLY TO ANY CLAIMS FOR PERSONAL INJURY. THIS AGREEMENT AND ANY CLAIMS AND DISPUTES BETWEEN THE
PARTIES SHALL BE GOVERNED BY AND SUBJECT TO THE INTERNAL LAWS (EXCLUSIVE OF THE CONFLICTS OF LAW PROVISION) AND DECISIONS OF
THE COURTS OF THE STATE OF ILLINOIS. THE EXCLUSIVE VENUE AND JURISDICTION FOR ALL CLAIMS AND DISPUTES SHALL BE THE STATE OR
FEDERAL COURT LOCATED IN SCHAUMBURG, ILLINOIS.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.
OUR EXCLUSIVE OBLIGATION, AND YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY OR OTHERWISE
SHALL BE THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR PARTS WHICH MAY PROVE DEFECTIVE UNDER THE
CONDITIONS OF NORMAL USE DURING THE WARRANTY PERIOD. IN THE EVENT THE PRODUCTS OR PARTS CANNOT BE
REPAIRED OR REPLACED, YOU SHALL RECEIVE A PRODUCT OF COMPARABLE VALUE AT OUR EXPENSE. AEROBED
WARRANTY IS NON-TRANSFERABLE, AND IS VALID FOR THE FIRST, ORIGINAL PURCHASER FROM AN AUTHORIZED
DEALER OF AEROBED PRODUCTS. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
CARE AND MAINTENANCE
1. Inspect your bed prior to each use.
2. Keep your bed away from any sharp objects or obstacles with rough edges. Large cuts or snags may not be repairable and will
not be covered by your bed warranty.
3. We recommend that you do not let the plush surface of your AeroBed get wet. Repeated exposure to water or other liquids
may cause damage to the plush surface that will not be covered by your warranty. Should liquid come in contact with the plush
surface, blot liquid dry and use a damp cloth to remove any stain. Let surface air dry completely.
4. You may clean the PVC on the sides and bottom of your AeroBed with a mild dishwashing detergent or household cleaner. Do not use strong
chemicals or other compounds. Allow your bed to air dry completely after cleaning and before storing.
®
www.aerobed.com
DEFLATION AND STORAGE
1. To deflate your AeroBed, open the valve located next to the pump (see figure C).
2. For most compact storage, open protective cap by turning counter-clockwise.
3. Press the port on top of the pump into the valve and then turn pump to “on” position (see figure D).
4. Your bed will begin to deflate, once deflated turn pump to “off” position.
5. Roll the bed completely until all the air is expelled. When the bed is completely rolled, replace the valve cap by turning clockwise.
6. Fold sides of bed into the center along its length (see figure E). Tightly roll and place in convenient carry bag for easy transport and storage.
UNIVERSAL ADAPTERS
For use with other air-filled products.
1. Attach universal adapter to end of pump by pushing until adapter locks into position.
2. Additional adapters are included for use with multiple sized valve openings.
3. Use pump with other products.
C
E
D
deflation port
Aero Products International, Inc. neither assumes nor authorizes any representative or other person to assume any obligation or liability other than those
expressly set forth herein.
© 2010 Aero Products International, Inc. All rights reserved. 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173 USA
This product may be covered under one or more of the following U.S. and/or foreign patents: U.S. Pat. Nos. 4,977,633; 5,267,363; 5,367,726; 6,237,621;
6,508,264; 6,598,626; 6,701,559; 6,755,208; 6,986,360; 6,996,867; 7,025,576; 7,039,972; 7,165,283; 7,128,525; 7,644,724; D464,225; D490,635; D513,145;
D594,880; CN 1809683.2; RU 2271129; SG93011; EP 0 487 641; DE 69024962.4; EP 0 947 152; DE 69233298.7; EP 1 415 576; EP 0 605 624;
DE 69230797.4; JP 3,419,774; TW 62301; AU 731613; BR PI9710873-1; CN 97196557.9; HK 1025374; MX 216898; NZ 334203; SG 61207; JP 2010828;
EP 1 359 325; MX 242683; AU 319268; ECD 00819289; ECD 00906920
Other U.S. and foreign patents pending.
Made in China.