Altec Lansing 2100 - Manual (Page 5)

TROUBLESHOOTING TIPS
SOUND PRESSURE LEVEL (SPL): 102 DB
Total Continuous Power: 35 Watts RMS
Front Speakers: 7 Watts/channel @ 4 ohms @
10% THD @ 200 - 22000 Hz 2
Channels Loaded
Subwoofer: 21 Watts @ 4 ohms
@ 10% THD @ 14 – 180 Hz
Single Channel Loaded
System Response: 40 Hz - 20 kHz (-10 dB)
Signal to Noise Ratio @ 1 kHz input: > 65 dB
SATELLITE AMPLIFIED SPEAKERS
Speaker Drivers (per Satellite): Two 1" (28 mm) micro drivers
SUBWOOFER
Speaker Drivers: Two 4" (102 mm) drivers
POWER REQUIREMENTS
USA/Canada/and applicable 120v 60Hz AC
Latin American countries:
Europe/United Kingdom; 230v 50Hz AC
applicable Asian countries;
Argentina, Chile and Uruguay:
ETL / cETL / CE / NOM / IRAM Approved
Find more troubleshooting tips in the FAQs located in the Customer
Support area of our web site: www.alteclansing.com.
Q. When connected to my computer sound card, should I use the
Windows volume control to adjust the volume of my speakers?
A. No. Adjust the Windows controls to about center as a starting point
and then use the speaker controller to adjust volume control. If the
volume is turned too high on the sound card, it can distort the sound.
Q. One, and sometimes both of my speakers do not work.
A. Check the input cable from speaker to the audio source and make
sure that it is connected to the line-out jack, which is the un-amplified
source. Make sure all the cables are plugged in correctly and have a good
connection. Still not working? Then try unplugging the cable from the
back of the computer, and insert the stereo plug into the headphone jack
of an alternate source (e.g., Walkman, Discman or FM radio) and play
music. If the speakers work, you may need to adjust your volume and
balance controls in your audio source, or Windows, if connected to your
computer's sound card
Q. My speakers give off a crackling sound (or static, or other noise).
What could be wrong?
A. Check all cables and make sure that they are connected to line-out or
audio-out jack on your sound card or other audio source, and NOT
speaker-out. If your audio source is your computer, check the volume
control in Windows: make sure that it is not set more than halfway.
Setting this level too high can cause sound distortion. If this does not
stop the noise, unplug the cable from the audio source and use an
alternate source (e.g., Walkman, Discman or FM radio) by plugging the
stereo cable into the headphone jack. If the noise goes away, you may
have a problem with your audio source.
Q. What can cause radio feedback?
A. If you are living near a radio tower you could have interference
caused by radio frequency. Try moving your speakers to see if the
interference goes away; if not, you may be able to purchase a stereo
cable from your local retailer that has a higher percentage of shielding.
Q. Can I hook my speakers to my TV or Stereo?
A. Yes, as long as your TV or Stereo has an unamplified source which is
line-out (check your TV or Stereo owners manual). These speakers may be
used with any audio device that has a stereo headphone jack. You may
also need a cable that has RCA jacks on one end and a 1/8 inch stereo
connector at the other end (these may be purchased at most local
electronics stores).
Q. I have very little bass coming from my Subwoofer. How do I increase
the bass output?
A. Adjust the BASS control through your audio sound source (computer
sound card control, CD player control, etc.). Check to make sure that all
of your cables are hooked up correctly and are making a good
connection.
Q. I have a low hum coming from my Subwoofer. Is this normal?
A. Yes. The AC in your house is at 60 cycles per second, which is within
the audio frequency of your subwoofer. Some low hum is natural and can
be detected when your speaker system is powered on without source
audio playing, or when volume is set at an extremely low level.
Q. I have a loud hum coming from my Subwoofer. What should I do?
A. Move the power cord from the power surge protector (if applicable)
and plug directly into an AC wall outlet. Move your cables and check to
see that they are making a good connection. If you disconnect your
stereo cable from the audio source and the loud hum goes away, then
you may need to adjust the volume control in your audio source as you
may be overdriving the volume settings on your speaker system. If you
are using your 2100 speakers with your computer system, just click on the
speaker icon located next to the digital clock to the lower right of your
Windows 9X or 2000 screen and adjust the volume.
Q. When I put my Subwoofer on my desk my monitor distorts. Why?
A. The Subwoofer is not magnetically shielded, and this can cause
distortion if it is less than 3 feet from your monitor.
Q. Where should the volume control be set on my Subwoofer?
A. Start with it in the center position then adjust to your preference.
Q. The DIN connector from the controller has multiple pins on one end,
and when trying to attach this cable I noticed that some of the pins are
bent, so I am not able to insert the cable into Subwoofer. What should I do?
A. Try to gently straighten the pins with tweezers or very small pliers. If
this does not work, then contact the Altec Lansing Consumer Support
Department for further instructions.
SPECIFICATIONS
4
Power rating conforms to FTC Amplifier Rule #16 C.F.R. Part 432. Altec Lansing’s superior sound comes from our patented Dynamic EQ
technology, which utilizes custom-built, high-fidelity drivers, state-of-the-
art equalization circuitry, and a harmonious mix of the following
specifications: