Vaddio Hot-Shot Preset Camera Controller - Manual (Page 8)

Hot Shot Preset Camera Controller
Hot Shot Preset Camera Controller - Installation and User Guide - Document Number 342-0124 Rev D Page 8 of 16
Table - Dip Switch Assignments
: The following table identifies the dip switch settings in detail. Set these
switches according to the application requirements of the installation.
Function / Dip Switch SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10
Vaddio Default ASCII
Up Up Up Up - - - - - -
Polycom Codecs Down Up Up Up - - - - - -
TANDBERG C-Series Codecs
Up Down Up Up - - - - - -
TANDBERG MXP Codecs
Up Up Down Up - - - - - -
LifeSize Codecs Up Up Up Down - - - -
Vaddio PTZ Camera
Programming Mode
Down - - - Down - - Down - -
Vaddio PTZ Cameras Preset
Playback Mode
Up Up Up Up Down - - - - -
Trigger Last Step
- - - - - - Up - - -
Trigger First Step - - - - - - Down - - -
Default Idle Return to Preset 1
(Preset 0 on Polycom and
TANDBERG Codecs)
- - - - - - Up - -
Default Idle Return Off - - - - - - - Down - -
Hot-Shot Address Master 0
- - - - - - - - Up Up
Hot-Shot Address Slave 1
- - - - - - - - Up Down
Hot-Shot Address Slave 3 - - - - - - - - Down Up
Hot-Shot Address Slave 4
- - - - - - - - Down Down
Notes:
1) The Vaddio PTZ Camera Programming mode is used to program Presets 7 through 16 on the Vaddio PTZ Camera.
2) The Vaddio PTZ Camera Playback mode is turned on to trigger the stored presets inside the camera. Dip Switch 5
must be down in both Programming and Playback modes.
Control Protocols and Strings:
When a preset number is triggered, for example Preset # 2
* , the ASCII Output Strings are automatically output in
the following formats:
 Vaddio Default ASCII: Preset 2<cr><lf>
 Polycom
* :
preset near go 3<cr><lf>
 TANDBERG C-Series: xcommand preset activate presetid:2<cr><lf>
 TANDBERG MXP Series
*
: presetactivate number:3<cr><lf>
 LifeSize **
:
set camera position -P 2<cr><lf>
 Vaddio PTZ Cameras (HEX) 81 01 04 3F 02 01 FF
The Vaddio Default ASCII, Vaddio Camera Hex and the TANDBERG C-Series have no offset to the preset
numbers.
* For Polycom and TANDBERG MXP codecs have a Preset “0”. Presets on the Hot-Shot are offset by -1 (for
example; 1 = 0, 2 = 1, 3 = 2 and so on).
** For LifeSize Codecs: The “0” key, when used as a preset, always moves the selected camera to the default
position and cannot be overwritten. There is no offset to the Hot-Shot and LifeSize preset numbers.
Note:
All commands are followed by a carriage return <cr> and line feed <lf> except Vaddio Cameras
Physical Connection:
The RS-232 connection between the Hot-Shot and the codec varies from codec to codec depending on the
manufacturer. The following RS-232 connections are required for proper operation:
 Hot-Shot to Polycom Codec: 9-Pin Female to Female Cable - Null Modem
 Hot-Shot to TANDBERG Codec: 9-Pin Female to Male Cable - Straight Through
 Hot-Shot to Life Size Codec: 9-Pin Female to Female Cable - Null Modem
 Hot Shot to Vaddio Cameras: Control Adapter (998-1001-232) 9-Pin Female to RJ-45F - Cat-5e to
RJ-45 of Camera