Vaddio OneLINK - Manual (Page 8)

OneLINK
OneLINK for Cisco Precision HD Cameras - Installation and User Guide 342-0122 Rev. G Page 8 of 12
Step 9:
With the Codec turned off, connect the 48 VDC power supply to the Quick-Connect OneLINK. The blue LED
power light will illuminate and it is ready for the codec to be booted up.
Note: If the OneLINK Cat-5e cable is incorrectly terminated or if intermittent connections are the result of the
use of pass-thru, EZ type RJ-45 connectors, damage to the system may result. If the units are damaged due to
improper cabling, then all implied or expressed warranties are automatically voided. Test your cables and use
standard RJ-45 connectors and crimpers.
Step 10:
Boot up the codec and the camera will be recognized. Normal IR control operation is available after boot up.
Note A: The system boot order should always be OneLINK first then Codec to follow.
Note B: If using a daisy-chain cable, first boot up the system as described above, then connect the daisy-chain
cable between cameras. If power is lost, the daisy chain must be re-initialized and connected last.
General Specifications
OneLINK
Part Numbers: 999-9550-000 - North America,
999-9950-001 - International (with UK and Euro AC Cord Set)
Connectors Quick-Connect OneLINK:

Vaddio Blue LED Power Indicator
 5.5mm OD x 2.5mm ID Coaxial Power Connector
 OneLINK port on RJ-45
 HDMI
 RS-232
on RJ-45
EZIM OneLINK:

5.5mm OD x 2.1mm ID Coaxial Power Connector
 RJ-45 for RS-232,
 HDMI

OneLINK port on RJ-45
Max. Cat 5e Cable Length Single Cat 5e up to 125’ (38.1m)
Power Supply 48 VDC, 1.4 Amp PowerRite Power Supply with AC Cord Set
EZIM OneLINK Regulates the Power to the Camera down to 12 VDC
Dimensions (H x W x D) Quick-Connect: 1.47” (37.34mm) H x 8.0” (203.2mm) W x 4.5” (114.3mm) D, (1/2Rack Size)
EZIM: 3.3” (83.8mm) H x 4.3” (109.2mm) W x 1.25” (31.75mm) D
Included Patch Cables for EZIM
and PrecisionHD Camera One (1) 1’ (30.5mm) HDMI Cable, One (1) 1’ (30.5mm) Cat-5e Patch Cable, One (1) 1’ (30.5mm)
5.5mm OD x 2.1 ID Power Cable
Weight Quick-Connect and EZIM - 2.1 lbs. (0.952543977 kg, give or take)
Accessory Options 998-6000-003 1-RU Dual Rack Mount Plate
Compatible Cameras
(Cameras Not Included) Cisco PrecisionHD 1080p 12x and PrecisionHD 720p
(PrecisionHD 1080p4x is not supported except at the end of a daisy chain configuration since it
doesn’t have a daisy-chain port. The PrecisionHD 10804xS2 is not supported.)
Compatible Codecs Cisco C-Series; C20, C40, C60 and C90 (Codecs Not Included) (SX-20 Codec is not supported)
Safeguards Do not use the cable # 116627, DB-9M to RJ-45, to connect the OneLINK to the camera control
port of the Codec. The OneLINK will be damaged and the warranty will be voided.
Connect the 48VDC
PowerRite Power
Supply Last
To/From EZIM OneLINK
at Camera Location
To HDMI Input of
Cisco C-Series
Codec
To & From Camera Control Port of
Cisco C-Series Codec - Use a Cat-5e
patch cable (568B) and the 998-1008-
232 to make this connection.
Do not
use the Cisco #116627 cable provided
with the codec.