Silverline 1600W Wall Chaser 150mm - Manual (Page 6)

www.silverlinetools.com
5
Wall Chaser 150mm 817089
Power Tool Use & Care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at
the rate for which it was designed
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired
c) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users
e) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may
affect the power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by poorly
maintained power tools
f) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control
g) Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working
conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous
situation
Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of
the power tool is maintained
Additional Safety Instructions for
Wall Chasers
WARNING. Before connecting a tool to a power source (mains switch power
point receptacle, outlet, etc.) be sure that the voltage supply is the same as
that specified on the nameplate of the tool. A power source with a voltage
greater than that specified for the tool can result in serious injury to the
user, and damage to the tool. If in doubt, do not plug in the tool. Using a
power source with a voltage less than the nameplate rating is harmful to
the motor.
Use the correct cutting tool
• Ensure the cutting tool is suitable for the job. Do not assume a tool is
suitable without checking the product literature before use
Protect your eyes
• Always wear appropriate eye protection when using cutting tools
• Spectacles are not designed to offer any protection when using this
product; normal lenses are not impact resistant and could shatter
Protect your hearing
• Always wear suitable hearing protection when tool noise exceeds 85dB
Protect your breathing
• Ensure that yourself, and others around you, wear suitable dust masks
Be aware of others around you
• It is the responsibility of the user to ensure that other people in the
vicinity of the work area are not exposed to dangerous noise or dust and
are also provided with suitable protective equipment
Beware of projected waste
• In some situations, waste material may be projected at speed from the
cutting tool. It is the user’s responsibility to ensure that other people in
the work area are protected from the possibility of projected waste
• Be aware that the cutting blades will project from the underside of the
tool. Ensure that all supports and power cables are completely clear of
the cutting path
• Always ensure that an appropriate blade is used for the material being cut
• Always use a suitable detector to check there are no hidden cables or
pipes where you propose to cut
• Do not apply the blade to the wall until the motor has reached full speed
• Choose a stable working position and always hold the tool firmly with
both hands
• Do not apply any sideways or twisting force to the blade whilst cutting
Accessories
• 1 pair spare carbon brushes
• 2 x diamond cutting discs (fitted)
1 Spindle Lock
2 Trigger Switch
3 Lock-Off Button
4 Rear Handle
5 Motor Cover
6 Front Handle
7 Baseplate
8 Depth Lock
9 Blade Guard
10 Dust Extraction Port
11 6mm Hex Key
12 Pin Spanner
13 Chisel
Product Familiarisation
817089_Z1MANPRO1.indd 5 16/11/2012 14:24