Silverline 2050W 1/ Plunge Router - Manual (Page 5)

4
GB
Clean the work area
• Accidents can occur where benches and work areas are cluttered or dirty. Keep
floors clear and avoid working where the floor is slippery. If working outdoors,
be aware of all potential slip and trip hazards before using this tool
Trained, competent persons
• This tool should be used by trained, competent persons only
Children and pets
• Keep children and pets at a safe distance from the work area. Lock tools away
where children cannot gain access
Use the correct tool
• Do not force or attempt to use a tool for a purpose for which it was not
designed. This tool is not intended for industrial use
Wear suitable clothing and footwear
• Do not wear loose fitting clothing, neckties, jewellery, or other items which may
become caught. Wear non-slip footwear or, where appropriate, footwear with
protective toe caps. Long hair should be covered or tied back
Keep your balance
• Do not over-reach. Keep proper footing at all times and do not use tools when
standing on an unstable surface
Accessories
• The use of any attachment or accessory, other than those mentioned in this
manual, could be dangerous and result in damage or injury, and may invalidate
your warranty
Never stand on your tool
• Standing on your tool or its stand could cause serious injury if the tool is tipped or
collapses. Do not store materials above or close to the tool in such a way that a
person might stand on the tool to reach the stored items
Secure work
• Where possible, always secure work. If appropriate, use a clamp or vice so that
both hands are free to operate the tool
Check for damaged or missing parts
• Before each use, check if any part of the tool is damaged or missing. Carefully
check that it will operate properly and perform its intended function. Check
alignment of moving parts for binding. Any guard or other part that is damaged
should be immediately repaired or replaced by an authorised service centre.
DO
NOT USE IF DEFECTIVE
Electrical Safety
The wires in this product are coloured:
Blue Neutral
Brown Live
Green & Yellow Earth
• This appliance must be protected by a suitable fuse
• To prevent fire or shock hazard, do not expose this product to rain, water or
moisture
• There are no user-serviceable parts inside except those referred to in this
manual
• Always refer servicing to qualified service personnel. Never remove any part of
the casing unless qualified to do so; this unit contains dangerous voltages
• Use of a residual current device will reduce the risk of electric shock
NEVER CONNECT THE BROWN OR BLUE WIRE TO THE EARTH PIN OF A 13A
PLUG. IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN
Dangerous environment
• Do not use power tools in damp or wet conditions, or expose them to rain.
Provide adequate surrounding work space and keep the area well lit. Do not use
power tools where there is a risk of explosion or fire from combustible material,
flammable liquids, flammable gases, or dust of an explosive nature. When using
Specification
Voltage ......................................230V~
Frequency ..................................50Hz
Power ........................................2050W
No load speed ............................6000-24000min -1
Collet size ..................................1⁄4", 1⁄2", 8, 10 & 12mm
Weighted vibration .....................4.77m/s 2
Uncertainty.................................1.5m/s²
Sound pressure .........................92.4dB(A)
Sound power .............................103.4dB(A)
Uncertainty.................................3dB(A)
Protection Class .........................
The sound intensity level for the operator may exceed 85dB(A) and
sound protection measures are necessary.
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
General Safety
Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe
manner in which to use this tool, do not attempt to use it.
Keep guards in position
• Where guards exist keep them in position, in good working order, correctly
adjusted and aligned. Never attempt to use a tool if any of the supplied guards
are missing. If any guards are damaged, replace before use
Remove adjusting keys
• Where adjusting keys exist, ensure they are removed prior to using the tool.
Always check to see that keys and adjusting devices are removed from the
tool before use
Description of Symbols
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction Manual.
Double insulated for additional protection.
Conforms to relevant legislation and safety standards.
Environmental Protection
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check
with your local authority or retailer for recycling advice.
124799_Z1MANPRO1.indd 4 29/07/2011 14:51