SawStop 3.0HP - Manual (Page 114)

No. Description Part No. Qty.
36 Miter Gauge Head PCS-226 1
37 8-32 NCx5/8” Phillips Head Screw PCS-227 3
38 8-32 NC Nut PCS-228 3
39 Miter Gauge Handle PCS-229 1
40 M8x18x3 Washer PCS-230 1
41 Miter Gauge Bar PCS-252 1
42 Gauge Head Mounting Screw PCS-232 1
43 M6x1.0x8 Pan Head Phillips Screw PCS-233 1
44 Retaining Disc PCS-234 1
45 M5x0.8x12 Spring Bearing PCS-251 3
112 SawStop 10” Professional Cabinet Saw
Literature, Hardware and Tools Parts List
No. Description Part No. Qty.
1 SawStop 10” Professional Saw Owner’s Manual PCS-235 1
2 Table Saw Hardware Pack PCS-236 1
3 Unpacking Procedure Poster PCS-237 1
4 Hex Key Tool Holder (includes M3, M4, M5, M6 hex keys) PCS-238 1
5 M8 Ball End Hex Key PCS-239 1
6 Blade Spacing Adjustment Gauge PCS-240 1
7 Push Stick PCS-241 1
1
4 5 6
2 3
7
OWNER’S MANUAL
10” PROFESSIONAL
CABINET SAW
Models PCS31230, PCS175
SawStop ®
Suggested Procedure for Unpacking Your Saw
! WAR NING D o n ot o pe ra te w ith d oo r o pe n. Th e b la de c an re tra ct a nd ca us e a s ev ere in ju ry if y ou to uc h i t i ns id e the ca bin et. A lso , m ov ing p ar ts c an cu t, p in ch o r c ru sh .
! W AR N IN G M o v in g g ea
rs a n d p ar
ts c an
p in ch , c u t o r c ru sh . D o n o t o p er a te w it h d o o r o p en
.
! WAR NING Do no t op erate wi th doo r op en. The bla de can ret rac t an d c aus e a se vere inj ury if y ou tou ch it in sid e the cab ine t. A lso , m ovi ng par ts ca n cut , pi nch or crus h .
1. Remove all packing materials and accessories before
removing the saw from the shipping pallet (see Fig. 1).
IMPORTANT - An exploded view of the accessories
and where they are packaged can be seen on the
other side of this poster.
Fig. 2
Fig. 1
Fig. 3
3. With the help of an assistant, carefully roll the saw
onto the top piece of Styrofoam, as shown in Fig. 3. You
can use the cast iron table and the elevation control shaft
as lifting points to help you roll the saw. The saw weighs
approximately 265 pounds; do not attempt to move it by
yourself. Wear safety gloves and be careful to use proper
lifting technique to avoid injury.
Fig. 4
4. With the help of an assistant, carefully tip the
saw to the upright position by lifting under the rear
edge of the cast iron table (see Fig. 4). While
tipping the saw, gently lower the bottom edge of
the saw to the floor to avoid damaging the saw.
Read and understand the owner’s manual fully
before assembling and operating your saw.
2. Take the top piece of Styrofoam and
place it next to the rear edge of the pallet, as
shown in Fig 2. Make sure that the
Styrofoam is placed so that the top edge of
the table and the bottom edge of the saw
both overhang the edges of the Styrofoam.
the edge of the table
should overhang the
edge of the Styrofoam
the bottom edge of the saw should overhang the edge of the Styrofoam
use the table and the elevation control shaft
as lifting points to help
roll the saw
lift under the rear
edge of the table
top piece of Styrofoam
SawStop
Mounting the Switch Box
Hardware for Step 7
Button Head Socket Screws,
M6 x 20 (2)
9
Switch Box
Keys (2)
Installing the Handwheels
Hardware for Steps 2-3
1 Keys, 5 x 5 x 25 (2) Set Screws, M6 x 8 (2)
2
Mounting the Dust Port
Hardware for Step 4
Mounting
the
Motor
Cover
Hardware for Step 5
F
Mounting the
Wrench & Tool
Holders
Hardware for Step 8
Motor
Cover
Rod
5
Blade
Wrench Holder
13
Button Head
Screws,
M6 x 12 (2)
15 Lock
Washers,
M6 (2)
14
12
Mounting the Extension Wings
Hardware for Step 6
Washers, M8 (8) 6 Hex Bolts, M8 x 16 (8) 8 Lock Washers, M8 (8) 7
Tools
Lock Washers, M6 (2) 10
Washers, M6 (2) 11
Hex Key, M8 (1)
Blade Spacing
Adjustment Gauge (1)
Hex Keys: M3 (1), M4 (1), M5 (1), M6 (1)
Pull tab to remove hardware pack
Pull tab to remove hardware pack
T
a
ble Saw Hardware Pack
Lock Washers, M5 (3) 4 Button Head Screws, M5 x 3 x 15 (3) 3
Blade Guard and Miter Gauge Parts List