RADWAG Low profiled scales User Manual

User manual, 4 load cell platform scales

Advertising

This manual is related to the following products:

Mild steel scales Stainless steel scales Stainless steel scales (pit version) Ramp scales Pallet scales Beam scales

Table of contents

Document Outline

1. INTENDED USE
2. PRECAUTIONS
- 2.1. Maintenance
- 2.2. Accumulator / battery pack
  - 2.2.1. Power supply of weighing indicators in plastic casings
  - 2.2.2. Replacement of worn batteries
- 2.3. Operation in a strong electrostatic field
3. WARRANTY CONDITIONS
4. MAIN DIMENSIONS
- 4.1. Low profiled scales
- 4.2. Ramp scales
- 4.3. Stainless steel scales
- 4.4. Stainless steel scales (pit version)
- 4.5. Mild steel scales
- 4.6. Pallet scales
- 4.7. Beam scales
5. ASSEMBLY AND LEVELLING
- 5.1. Assembly of scales
  - 5.1.1. 4 load cell platform scales
  - 5.1.2. Ramp scales
- 5.2. Levelling the scale
6. GETTING STARTED
7. KEYPAD
8. KEYS’ FUNCTIONS
9. INSCRIPTIONS ON THE DISPLAY
10. USER MENU
- 10.1. Submenus
- 10.2. Browsing user menu
  - 10.2.1. Keypad
  - 10.2.2. Return to the weighing mode
11. WEIGHING
- 11.1. Tarring
- 11.2. Inscribing tare value
- 11.3. Zeroing
- 11.4. Weighings in two ranges
- 11.5. Selection of basic weight unit
- 11.6. Temporarily selected unit
12. MAIN PARAMETERS
- 12.1. Setting a filtering level
- 12.2. Median filter
- 12.3. Autozero function
- 12.4. Tare function
13. RS 232 PARAMETERS
- 13.1. Printout type
- 13.2. Minimal mass threshold
- 13.3. Baud rate
- 13.4. Serial transmission parameters
14. OTHER PARAMETERS
- 14.1. Backlight function
  - 14.1.1. Backlight for supplying from mains
  - 14.1.2. Backlight for supplying from batteries
- 14.2. “Beep” signal – after pressing a key
- 14.3. Automatic switch-off
- 14.4. Battery voltage level check
15. WORK MODES
- 15.1. Setting accessibility of operation modes
- 15.2. Selecting quantity of operation modes
- 15.3. Counting pieces of the same mass
- 15.4. +/- control referring to the inscribed standard mass
- 15.5. Control of % deviation referring to the inscribed standard mass
  - 15.5.1. Standard mass determined by its weighing
  - 15.5.2. Mass of standard inscribed to scale memory
- 15.6. Automatic tare
- 15.7. Measurement max force on the pan – latch
- 15.8. Totalizing
- 15.9. Weighing animals
- 15.10. Tare memory
  - 15.10.1. Entering the tare value to the scale memory
  - 15.10.2. Selecting a tare value from the memory
16. USER CALIBRATION
- 16.1. Calibration
- 16.2. Start mass adjustment
17. COOPERATION WITH PRINTER
18. COOPERATION WITH COMPUTER
19. COMMUNICATION PROTOCOL
- 19.1. General information
- 19.2. A set of commands for RS interfaces
- 19.3. Respond message format
- 19.4. Command’s description
- 19.5. Manual printouts / automatic printouts
- 19.6. Continuous transmission
- 19.7. Configuring printouts
20. ERROR COMMANDS
21. TECHNICAL PARAMETERS
- 21.1. Mild steel scales
- 21.2. Stainless steel scales
- 21.3. Stainless steel scales (pit version)
- 21.4. Ramp scales
- 21.5. Low profiled scales
- 21.6. Pallet scales
- 21.7. Stainless steel pallet scales
- 21.8. Beam scales
- 21.9. Beam scales (stainless steel)
22. TROUBLE SHOOTING
23. ADDITIONAL EQUIPMENT