NITECORE P20UV - Manual

®
User Manual
Features
• Features dual light sources: one main LED plus four secondary ultraviolet LEDs.
Purpose built for authentication, forensics and identification applications.
• White CREE XM-L2 (T6) LED provides maximum output of 800 lumens
• Four ultraviolet LEDs provide 320mW at 365nm
• Maximum runtime of 15.5 hours on lowest output.
• Metal micro textured reflector provides a wide cone of peripheral light.
• Dual tail switches ensure ease of use and tactical advantages
• STROBE READY
TM provides direct access to strobe mode in any state (patented)
• Features three selectable modes
• Tail switch features integrated power indicator to display remaining battery power
(patented)
• Anti-rolling design
• Two-way titanium steel clip included
• Toughened ultra-clear mineral glass with anti-scratch coating
• Constructed from aero grade aluminum alloy with HAIII military grade hard-anodized
finish
• Waterproof in accordance with IPX-8 (two meters submersible)
• Impact resistant to 1.5 meters
Dimensions
Length: 134mm (5.28”)
Bezel Diameter: 31.8mm (1.25”)
Tail Diameter: 25.4mm (1”)
Weight: 104grams (3.67oz)(without battery)
Thanks for purchasing NITECORE!
Brightness & Runtime
The All-Round Flashlight Expert
Accessories
Included: quality holster, CR123 battery
magazine, clip, tactical ring, lanyard, spare
O-ring
Optional: holster NTH30B, remote switch
RSW2, tactical lanyard NTL10/NTL20
Battery Options
Operation instructions
Battery installation
Install one 18650 Li-ion battery or two
CR123 Li-ion batteries with the positive
pole pointing forward (toward the bezel).
NOTE: Integrated LEDs within the tail
switch will blink to indicate remaining
battery power after battery installation.
Please refer to Power Tips for more
information.
WARNING
1. Install batteries as instructed. Incorrect
batteries installation will stop the torch from
functioning.
2. The NBM1618 battery magazine holds 2
x CR123 batteries, inhibits batteries
movement inside the compartment and
helps maintain electrical continuity.
3 This product CANNOT be powered by
flat-top batteries.
4. AVOID direct eye exposure.
Switching ON/OFF
To switch ON: press the tail switch until a “click” is heard;
To switch OFF: with the light turned on, press the tail switch again until a “click” is
heard.
Mode Selection
The P20UV offers three different modes of illumination for different users and
situations:
Tactical Mode: this mode only provides turbo and ultraviolet outputs, and is ideal for
self-defense, emergencies and tactical operations.
Law Enforcement Mode: this mode provides medium, turbo and ultraviolet outputs.
Turbo is the default state. This mode is designed for law enforcement officers and
patrol guards.
General Mode (default mode for first time use): this mode provides low, medium,
turbo and ultraviolet outputs. With the light turned on, press the STROBE READY
TM switch
on the tail to cycle through all four outputs. General mode provides an intelligent
memory function to ensure direct access to the setting last used when reactivated.
NOTE: 1. When using ultraviolet output, the P20UV is capable of sustaining a
constant output for 13 hours with 1 x 3.7V 2600mAh 18650 Li-ion battery;
2. When in medium and turbo mode, the P20UV will reduce output luminance
automatically after 3 minutes of use to prevent batteries from overheating and
extends battery longevity.
WARNING: Avoid eye or skin exposure to the ultraviolet light.
How to select a desired mode:
1. Ensure the P20UV is switched off.
2. Loosen the head of the torch.
3. Press and hold the STROBE READY
TM switch on the tailcap while simultaneously
tightening the head.
4. Once the head has been tightened, the P20UV will indicate the mode that has been
selected by flashing once for Tactical Mode, twice for Law Enforcement Mode and
three times for General Mode.
5. To cycle through all three modes, simply repeat the above procedures.
Strobe Ready
1. With batteries loaded and the light turned off, press and hold STROBE READY TM switch
on the tailcap to enter Strobe mode.To exit, simple release the switch.
2. With the light turned on in any state, press and hold STROBE READY
TM switch on the
tailcap for more than 0.5 second to enter strobe mode. To exit, simply press STROBE
READY
TM switch again.
Power Tips
Two integrated LEDs built into the tail switch blink to indicate remaining battery power
when the tail cap is tightened after battery installation. The power indicators will blink
three times when power levels are above 50%; twice when power levels are below
50%; and once when battery power is close to depletion.
NOTE: When batteries are already installed and a precise power reading is required,
ensure the P20UV is powered down for 20 seconds before retightening the tail cap to
detect battery power status.
Replacing Batteries
Batteries should be replaced when any of the following occurs: The power indicators
blink rapidly, output appears to be dim or the flashlight becomes unresponsive.
Maintenance
Every 6 months, threads should be wiped with a clean cloth followed by a thin coating
of silicon-based lubricant.
Warranty Service
All NITECORE® products are warranted for quality. DOA / defective products can be
exchanged for replacement through a local distributor/dealer within 15 days of
purchase. After 15 days, all defective / malfunctioning NITECORE® products will be
repaired free of charge for a period of 60 months (5 years) from the date of purchase.
Beyond 60 months (5 years), a limited warranty applies, covering the cost of labor
and maintenance, but not the cost of accessories or replacement parts. The warranty
is nullified in all of the following situations:
1. The product(s) is/are broken down, reconstructed and/or modified by unauthorized
parties.
2. The product(s) is/are damaged through improper use.
3. The product(s) is/are damaged by leakage of batteries.
For the latest information on NITECORE® products and services, please contact your
national NITECORE® distributor or send an email to [email protected]
The Nitecore official website shall prevail in case of any product data changes.
NOTE
The above data has been
measured in accordance with the
international flashlight testing
standards ANSI/NEMAFL1 using 1
x 3.7V 2600mAh Nitecore 18650
battery and 2 x 3V 1700mAh
Nitecore CR123 batteries under
laboratory conditions. The data
may vary slightly during real-world
use due to battery type, individual
usage habits and environmental
factors.
NITECORE (SYSMAX) is a member of PLATO, participating in and helping to develop
the ANSI FL1 standard of measurement. Product testing data is in accordance with
these internationally recognized scientific standards.
SIZE Nominal voltage Compatible
Primary Lithium battery CR123 3V Y (Recommended)
18650 Rechargeable Li-ion battery 18650 3.7V Y (Recommended)
Rechargeable Li-ion battery RCR123 3.7V Y
SYSMAX Industry Co., Ltd.
TEL: +86-20-83862000
FAX: +86-20-83882723
E-mail: [email protected]
Web: www.nitecore.com
Address： Rm1401, Glorious Tower, 850 East Dongfeng Road,
Guangzhou, China 510600
Please follow our facebook for
more info: NITECORE Flashlights
HIGH MID LOW
LUMENS
400
LUMENS
800
LUMENS
70
3 h 30 min 5 h 45 min 15 h 30 min
LUMENS
400
LUMENS
800
LUMENS
80
1 h 30 min 2 h 30 min 8 h
180m (Beam Distance)
8100cd
(Peak Beam Intensity)
IPX-8, 2m
(Waterproof AND Submersible)
1.5m
(Impact Resistant)
Momentary Illumination
Simply half press and hold the tail switch to turn on the flashlight, and release
to turn it off.
P20UV