AEG MC 4456 iP - Manual (Page 53)

English
53
11 STANDBY Indicator
12 DAB/FM/AUX button
13 CD/iPOD/USB/CARD button
14
SCAN/ENTER button (play/pause/Scan/Enter)
15 /MENU/INFO button
16 / SKIP/TUNE SEARCH buttons
(search forward/backwards)
17 Open/close docking port
18 Docking port compartment
Rear view (Fig. 2)
19 Mains switch
20 Mains cable
21 FM ANT. aerial antenna
22 headphone jack
23 LINE IN connection
Remote control (Fig. 3)
1 CD/iPOD/USB/CARD button
2 DAB/FM/AUX button
3 SELECT/MONO/ST. button
4
/ FOLDER buttons (up/down, album)
5 CLOCK DISP button
6 TIMER button
7 SLEEP button
8 VOLUME +/- (volume) buttons
9 INTRO button
10 MUTE (mute) button
11 EQ button
12 ID3/iPOD/MEM/C-ADJ. button (memory/clock)
13
/ SCAN/ENTER
(play/pause/Scan/Enter) button
button (Preset/search forward)
button (Preset/search backwards)
/ MENU/INFO (Stop/Menu) button
14 REPEAT button (repeat)
15 RANDOM button (random play)
16 STANDBY/ON button
Installation/Introduction
• Read the manual thoroughly before operating the de-
vice!
• Choose a suitable location for the device. Suitable loca-
tions are dry, even and anti-slip surfaces on which you
may operate the device easily.
• Make sure there is proper ventilation for the device!
• Remove, if necessary, the protection sheet from the
display.
Wall mounting
You can also mount the device to the wall (mounting acces-
sories not supplied).
CAUTION:
Make sure beforehand whether there are cables in the wall
which could be damaged!
NOTE: Check the reach of the cable!
To mount the device, make sure that an easily accessible
plug outlet is available within reach of the power cable.
The distance between the mountings for wall mounting is
140 mm.
• Drill two holes horizontally 140 mm apart.
• Fit rawlplugs and screws into the holes.
• Tighten the mounting screws until they protrude around
4 mm from the wall.
• Fold the stand up through 90° (see page 4, fig. 4).
• Mount the device onto the screws. Check that it is secure.
Insert/Replace Battery in Remote Control
NOTE:
Where necessary, the lithium cell in the battery compart-
ment of the remote has been fitted with a protective foil for
transport. This extends the lifetime of the battery. Before
initial use please remove this foil to prepare the remote for
use.
The battery in the remote is a long-life lithium cell. Should
the range of the remote shorten during use, follow the steps
below:
• Open the battery compartment on the underside of the
remote.
• Replace the cell with a battery of the same type
(CR 2032). Make sure the polarity is correct.
• Close the battery compartment.
If the remote is not in use for a lengthy period of time, please
remove the battery to prevent the battery acid from “leaking”.
WARNING:
• Do not expose batteries to intense heat or direct
sunlight. Never throw batteries onto a fire. Danger of
explosion!
• Keep batteries out of the reach of children. They are
not toys.
• Do not force batteries open.
• Avoid contact with metallic objects. (Rings, nails, screws
etc.) Danger of short circuits!
• Short circuits may overheat or even ignite batteries.
This may lead to combustion.
• When transporting the batteries, cover the terminals for
your safety with an adhesive strip.
• If a battery leaks, do not rub the fluid into the eyes or
the skin. If acid comes into contact with the eyes, rinse
with purified water and seek medical advice if symp-
toms persist.