AEG MR 4139 BT schwarz - Manual (Page 31)

English
31
First Use of the Device/Introduction
• Select a proper place for the device. A dry, level and slip
proof surface is suitable.
• Make sure the device is vented sufficiently!
• Remove the protective film from the device, if present.
Stromversorgung
• Insert the grid plug into a properly installed socket. Con-
nect the device with the plug connector by inserting its
plug into the DC 6 V jack of the device.
• Make sure the grid voltage corresponds to the figures on
the rating plate.
CAUTION:
• The included AC adapter may only be used with this
device. Do not use it for other devices.
• Use only an AC adapter with 6 V ( ). A different
AC adapter may damage the unit.
NOTE:
• Disconnect from mains power supply during longer
periods of non-use.
• The time and the stored radio stations are lost as soon
as the power supply has been interrupted.
Inserting batteries (batteries not included)
Alternatively, you may operate the device with batteries.
1. Open the battery compartment located at the back of
the device.
2. Insert 4 batteries of type R6/AA 1.5 V, thereby observing
the correct polarity (see bottom of the battery compart-
ment).
3. Close the battery compartment.
WARNING:
Do not expose batteries to extreme heat such as sunlight,
fire or the like. There is a
risk of explosion!
CAUTION:
• Batteries can leak battery acid. If you do not use the
device for a prolonged period of time, remove the bat-
teries from the device.
• Follow the instructions by the batteries’ manufacturer!
• Different battery types or new and used batteries must
not be used together.
• Do not dispose of batteries through normal household
waste. Return batteries to appropriate collection facili-
ties or retailers.
Setting the clock (during standby mode)
You may only set the clock when the clock time is displayed. If
necessary, switch off the device with the RADIO button.
1. Press and hold the SET button for approx. 3 seconds. The
hour indicator starts to flash.
2. Use UP/DOWN buttons to set the hours. Confirm with
SET.
3. Use UP/ DOWN buttons to set the minutes.
4. Use the UP/DOWN buttons to select the 24- or 12-hour
time format. Confirm with SET.
NOTE: When choosing the 12-hour time format, the
display shows
AM = morning, PM = afternoon.
5. Press SET again in order to save the time settings.
NOTE:
In case of power interruptions the clock time will be lost.
Light button
Press down the LIGHT button (14) to continuously light the
display. When pressing LIGHT again, the display backlight
will turn off time-delayed.
Switch (13)
Use this switch to select the following functions:
-
AUX IN • BLUETOOTH
The device supports AUX and Bluetooth operation.
Please refer to “Playing back music files” below.
- BUZZ
Listen to radio or set an alarm time. If an alarm has been
activated, the device will wake you with a signal sound.
- RADIO
Listen to radio or set an alarm time. If an alarm has been
activated, you will wake up to radio operation. The device
will switch on the radio station listened to last with the
volume set at the volume control.
Alarm function
You may only set the alarm time when the clock time is
displayed. If necessary, switch off the device with the RADIO
button.
Set the alarm time
1. Press the MODE button. The display will show ALM/SET
and the currently set alarm time.
2. Press and hold the SET button for approx. 3 seconds. The
hour indicator starts flashing.
3. Use UP or DOWN to set the hours. Confirm with SET.
4. Use UP or DOWN to set the minutes. Confirm with SET.
5. Use UP or DOWN to activate or deactivate the alarm
function. Alarm function activated: an alarm icon will be
displayed.
6. Press SET to save your settings.
7. At the end, press MODE to return to clock time mode.
8. Use the switch (13) to select your desired wake-up mode.
BUZZ = signal sound, RADIO = radio station listened to
last.