Olympus E-100 RS - Manual (Page 2)

http://www.olympus.com
OLYMPUS AMERICA INC.
Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A. Tel. 631-844-5000
(Customer support) Tel. 1-888-553-4448
2
Taking pictures
Taking still pictures
1. Set the Mode dial to P.
2. Compose the picture by turning the
camera towards the subject and centering
the AF target mark on the image you want
to shoot.
Press (Monitor button) to select whether to
display your image on the Monitor or the Viewfinder.
S M P rg A
P P F2.8 1/30 0.0
[ SM ]
[To enlarge your subject]
Press the Zoom lever toward “T” to enlarge your subject. To return to normal
magnification, press the Zoom lever back toward “W”.
3. Press the Shutter button halfway to focus.
The AF confirmation mark lights up in green in the
upper left corner and the camera beeps. Focus
and exposure (shutter speed/aperture) become
locked.
If the AF confirmation mark blinks, then the camera
is out of focus. If this happens, release the Shutter
button and move the AF target mark slightly. Then,
press the shutter button halfway again.
4. Press the Shutter button fully to take a
picture.
The free part of the memory gauge lights up and
the card access lamp blinks while the picture is
being recorded.
Continuous shooting is available even if the card
access lamp is blinking, unless the entire memory
gauge is lit.
If you are taking a picture in a dark environment,
the built-in flash will fire automatically if it has been
popped up.
P F2.8 1/30 0.0
[SM]
Press
halfway Press
fully
Viewfinder
AF target mark
AF confirmation mark
AF target mark
P F2.8 1/30 0.0
[SM]
Memory gauge
Card access
lamp
Flash mode
Macro mode
Slow shutter
synchronization flash
Auto
bracket
Flash intensity control
Card writing
Sound
record
Card error
Battery check
White balance
Self-timer/
Remote control
ISO
Number of storable
still pictures
Seconds that movies
can be shot
Card
Sequential shooting
Record mode
Pre-capture
AE memory
Stabilizer
Metering mode
Manual focus
AF system
Exposure
compensation
Full-time AF
3
Playing back pictures
Set the Mode dial to .
The last picture taken is played back.
● Use the Arrow pad to select the desired picture for playback.
: Plays back next picture.
: Plays back preceding picture.
: Jumps to the picture 10 frames ahead.
: Jumps to the picture 10 frames behind.
10
12.23.,00 21:56
x10
HQ
[ SM ]
*Press the Zoom lever toward “W” to display multiple
pictures at the same time (Index-display).
*Press the Zoom lever toward “T” to display a close-up.
Arrow pad
Still picture display (1-frame)
Index-display
1234 1235 1236
1237 1238 1239
1240 1241 1242
● Use the Arrow pad to select the desired picture for playback.
: Plays back movie pictures when held down continuously.
: Plays back movie pictures in reverse when held down
continuously.
: Jumps to the beginning of the movie.
: Jumps to the end of the movie.
● Press OK to pause the movie.
[ 1 / 2 ]
SM/CF
COPY
[ SM ]
MOVIE PLAY START
4
Erasing pictures
Unwanted images can be erased. You can erase one frame or all frames,
depending on your requirements.
To erase an unwanted image, first display it on the screen as described
in “ Playing back pictures” on this page.
3
1-frame erase
Press (Erase button) on the camera and
select “YES” on the confirmation screen using
the Arrow pad. Then, press OK.
All-frame erase
Press , then select “CARD SETUP”—“ ” using the Arrow pad. Press
OK. Select “YES” on the confirmation screen, then press OK again.
(To cancel, select “NO”, then press OK.)
OK YES NO
NO
YES
[ SM ]
Confirmation screen
[ 2 / 2 ] [ SM ]
CARD SETUP
MODE SETUP
OK YES NO
NO
YES
[ SM ]
Erasing a still picture Confirmation screen
5
Turning off the power
When you are finished using the camera, turn the power off after
checking that the card access lamp is not on.
● The picture on the screen will disappear when you turn the power off.
● If no operation is performed for 1 minute or more, the image on the screen goes off
automatically to avoid battery exhaustion (this function is called Sleep). To end Sleep,
perform any operation on your camera.
● When you store the camera, make sure to put the lens cap on.
Taking movie pictures
1. Set the Mode dial to .
The maximum available recording time appears on the Viewfinder.
2. Press the Shutter button fully to start movie recording and press it
again fully to stop.
The card access lamp blinks while the picture is being recorded.
Continuous shooting is available when the card access lamp stops blinking.
[Movie pictures]
will appear with pictures that can be played back as movies.
(1) Press (Menu button) to display the Menu.
(2) Select “MOVIE PLAY” and press on the Arrow pad.
(3) When “START” appears, press the OK button.
The card access lamp blinks for a moment, then the movie starts.
(4) Press when you are finished watching. The Menu reappears. Press again to
exit the Menu.
Control panel indications
Printed in Japan
ⅷ
Quick-Start Guide
ⅷ