Toshiba DVR18 - Manual (Page 41)

41 EN
In
troducti
on
Connecti
o
ns
Bas
ic Setup
P
layback
Ed
iti
n
g
V
CR Fu
ncti
on
s
O
th
ers
Fu
nc
ti
on
Set
u
p
Recordi
n
g
Timer Recording
You can set the unit to record up to 12 programmes,
up to a month in advance. Daily or weekly programme
recordings are also available.
• Be sure to set the clock before entering a timer
programming.
Insert a recordable disc or a tape with a
record tab.
1
In stop mode, press [TIMER PROG.].
“Timer Programming” list will appear.
2
Select “New Programme” using
[
U / D], then press [ENTER / OK].
• If there are 7 programmes or more, use
[ SKIP B / F] to turn the page.
3
Enter the date using [ U / D], then
press [ P].
Each time you press [ D] at the current date, the
timer recording date will change as follows.
e.g., 1st January
4
Enter the time to start and to end
using [
U / D], then press [P].
5 Select the channel number to record
using [
U / D], then press [P].
To record from the external input, select “AV1”,
“AV2”, or “AV3”.
6 Select the recording media (“DVD”
or “VCR”) using [
U / D], then press
[ P].
7 Select the recording mode using
[
U / D], then press [P].
Refer to “Recording Mode” on page 34 for DVD or
page 85 for VCR.
8
For DVB channel recording:
Select “STTL” to “ON” or “OFF”
using [
U / D].
If you set “STTL” to “ON”, subtitle will be recorded
too.
• When analogue channel is selected, “PDC” will
be displayed instead of “STTL”.
For analogue channel recording:
Select “PDC” to “ON” or “OFF”
using [
U / D].
Refer to “PDC (Programme Delivery Control)” on
page 42.
• When DVB channel is selected, “STTL” will be
displayed instead of “PDC”.
9
Press [ENTER / OK] when all
information required is entered.
Your programme setting is stored.
• To set another programme, repeat the steps 2 to
9.
• To exit, press [TIMER PROG.].
• When 2 or more programmes are overlapped,
“Timer programme overlapped” appears, and
the overlapped programme will be displayed in
blue. To correct the timer Programme, Refer to
“Checking, Cancelling or Correcting the Timer
Programming Information” on page 42.
10
Press [TIMER SET].
The icon will appear on the front panel display
and the unit enters to the timer-standby mode.
DVD-RW DVD-RW
Video
DVD-RW DVD-RW
VR
DVD-R DVD-R D DVD+R VD+RW W DVD+RW
D DVD+R VD+R DVD+R VCR VCR VCR
Timer Programming
1/1
0:00 THU 06/12
Date
06/12
07/12
Start
7:00
9:00
End
9:00
9:30
CH
901
902
New Programme
STTL
PDC
Daily
M-F (Mon.-Fri.)
01/01
31/01
W-SAT
W-FRI
W-SUN
Timer Programming
1/1
0:00 THU 06/12
New Program
Date
REC To Mode PDC
Start End CH
01/01
DVD SP OFF
SP 2:00
--:-- --:-- 901 BBC1
Timer Programming
1/1
0:00 THU 06/12
Date
06/12
07/12
07/12
Start
7:00
9:00
17:00
End
9:00
9:30
18:00
CH
901
902
903
New Programme
STTL
PDC
E9NG1BD_EN.book Page 41 Monday, April 7, 2008 5:54 PM