Toshiba SD2010 - Manual (Page 22)


E
ng
lis
h
DVD Menu Options
{ Vivid }
Select this to make the picture brighter.
{ Cool }
Select this to make the picture softer.
{ Personal }
Select this to personalize your picture color by
adjusting the brightness, contrast, tint and color
(saturation).
B
Use  /  to select a setting and press OK to
confirm.
C If you select { Personal }, then proceed to steps
D
~
G
.
 The setup menu appears.
Brightness
Contrast
Tint
Color
0
0
0
0
Close
D Press  /  to highlight one of the following options.
Brightness
Increase the value to brighten the picture or vice
versa. Choose zero (0) for average setting.
Contrast
Increase the value to sharpen the picture or vice
versa. Choose zero (0) to balance the contrast.
Tint
Increase the value to darken the picture or vice
versa. Choose zero (0) for average setting.
Color
Increase the value to enhance the colour in your
picture or vice versa. Choose zero (0) to balance the
colour.
E
Press  /  to adjust the setting that best suits
your personal preference.
F Repeat steps D ~ E to adjust your picture
preference.
G
Press  /  to select ＇ Close＇ and press OK to
confirm.
JPEG Interval
You can continuously playback all JPEG files
automatically. Set “JPEG Interval” to “5 Seconds”,
“10 Seconds” or “15 Seconds”.
A
In ' Video ', press  /  to select { JPEG Interval },
then press .
{ Off }
Plays back one file at a time.
{ 5 Seconds }
Plays back images in the form of a slide show at 5
seconds intervals.
{ 10 Seconds }
Plays back images in the form of a slide show at 10
seconds intervals
{ 15 Seconds }
Plays back images in the form of a slide show at 15
seconds intervals
B
Use  /  to select a setting and press OK to
confirm.
Using the Audio setup menu
A
Press SETUP on the remote control.
 The system setup menu appears.
:
:
:
Digital Output
Night Mode
Down Sampling All
Off
On
Language
Video
Audio
Misc
Rating
: 3D Effects Off
B Press  /  to select { Audio }, then press .
C
Press  /  to select an item, then press  to
access.
Example: { Night Mode }
 The options for the selected item appears.
 If the selection in the menu is greyed out, that
means the feature is not available or not possible to
change at the current state.
D
Use  /  to select a setting and press OK to
confirm.
Example: { On }
 The setting is selected and setup is completed.
E
To exit, press SETUP.
Digital Output
Select this if you connect to a multichannel decoder/
receiver.
A
In 'Audio', press  /  to select { Digital Output },
then press .
{ Off }
To deactivate the digital audio output. For example, if
you use the AUDIO OUT jacks to connect to a TV or
stereo system.
{ PCM }
Select this if the connected device is not capable of
decoding multichannel audio. The DVD player will
convert the Dolby Digital signal to PCM (Pulse Code
Modulation).
{ All }
Select this if the connected device has a built-in
multichannel decoder that supports one of the
multichannel audio format (Dolby Digital, DTS).
B Use  /  to select a setting and press OK to
confirm.
Tip:
-When playing MPEG, MP3 and set Digital Output to
{All}, the player will output PCM signals.
Night Mode
This mode optimizes playback of sound at low
volume. High volume outputs will be softened and
low volume outputs are brought upward to an audible
level.
A
In ＇ Audio＇, press  /  to select { Night Mode },
then press .
{ Off }
Turns off night mode feature. Select this to enjoy the
surround sound with its full dynamic range.
{ On }
Select this to set low volume output. This feature
is only available for movie discs with Dolby Digital
Helpful hint: Press  to go back to previous menu item.
Press SETUP to exit the menu item.