Toshiba BDX2000 - Manual (Page 36)

36 EN
FUNCTION SETUP
Set up the network connection settings in order to use the
BD-Live function with a BD-Live disc.
After you made IP address/DNS settings or when a LAN
cable is connected, always perform the connection test to
check if the connection is correctly made.
1 In stop mode, press [SETUP].
2 Use [K / L] to select , then press [ENTER].
3 Use [K / L] to select “Others”, then press
[ENTER].
4 Use [K / L] to select “Network Connection”,
then press [ENTER].
5 Use [K / L] to select “Connection Test”, then
press [ENTER].
Connection test will start automatically and the test result
will appear right after the connection test finishes.
• “Testing...” : The test is in progress.
• “Pass”
: Connection test is successfully
completed.
• “Fail” : Connection test failed.
Check the connection settings.
Press [ENTER] to go to the list of network status
confirmation screen.
6 Press [ENTER] to go back to the previous
screen, or press [SETUP] to exit.
Network settings are set to the following settings initially.
(In most cases, you can connect to the Internet without
making any changes to the default settings.)
If you want to set the network settings back to the default
settings as above (except “BD-Live Setting”), follow the
procedure below.
1 Follow steps 1 to 4 in “Connection Test” on
page 36.
2 Use [K / L] to select “Enable(Easy)”, then press
[ENTER].
• The unit will start the connection test automatically
and the test result will appear right after the test
finishes.
• After the connection test finishes, press [ENTER] to go
to network status confirmation screen.
3 Press [ENTER] to activate the network settings
and set the network connection automatically.
Press [SETUP] to exit.
In following cases, select “Enable(Custom)” to set each
setting as necessary.
- When connection test failed with the setting of
“Enable(Easy)”.
- When instructed by your Internet service provider to
make specific settings in accordance with your
network environment.
IP Address Setting / DNS Setting
1 Follow steps 1 to 4 in “Connection Test” on
page 36.
2 Use [K / L] to select “Enable(Custom)”, then
press [ENTER].
3 Use [K / L] to select “IP Address Setting”, then
press [ENTER] repeatedly to select the desired
setting.
Network Connection
Connection Test
[Setup] A “Custom” A “Others” A
“Network
Connection”
A
“Connection
Test”
Note
• If the connection test passes, you can enjoy the
BD-Live functions using the Internet without making
any extra settings.
• If the connection test fails, you may need to change
the MAC address settings of your router. You can
check the MAC address of this unit on
“Enable(Custom)” screen.
• “Connection Test” is not available when “Disable” is
selected in “Network Connection”.
xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx
Others
Connection Test
IP Address
Subnet Mask
Default Gateway
Primary DNS
Secondary DNS
then press ‘ENTER’.
Enable(Easy)
[Setup] A “Custom” A “Others” A
“Network
Connection”
A
“Enable
(Easy)”
- IP Address Setting Auto(DHCP)
- DNS Setting Auto(DHCP)
- Proxy Setting Do Not Use
- Connection Speed Auto
- BD-Live Setting Allow
Note
• The setting of “BD-Live Setting” will not be set back
to the default, even if you follow the procedure.
Enable(Custom)
[Setup] A “Custom” A “Others” A
“Network
Connection”
A
“Enable
(Custom)”
“Auto(DHCP)” : If your router has DHCP server
function, select “Auto(DHCP)”.
“Manual” : If your router does not have DHCP
server function, select “Manual”.
E5RJ0BD_EN.book Page 36 Tuesday, October 20, 2009 3:53 PM