Philips HAIRCLIPPER Series 5000 Cortapelos profesional - Manual

45-DAY
MONEY-BACK
GUARANTEE
If you are not fully satisfied with your Philips
Norelco Hair Clipper, send the product back
along with dated sales receipt and we’ll refund
you the full purchase price.
The Clipper must be shipped prepaid by
insured mail, insurance prepaid, and have
the original sales receipt, indicating purchase
price and the date of purchase, enclosed.
We cannot be responsible for lost mail.
The Clipper must be postmarked no later
than 45 days after the date of purchase.
Philips Norelco reserves the right to verify
the purchase price of the Clipper and limit
refunds not to exceed suggested retail price.
To obtain Money-Back Guarantee Return
Authorization Form, call 1-800-243-3050 for
assistance. Please allow 4-6 weeks for delivery
of check.
ENGLISH
1 Be certain Clipper is OFF.
2 Insert the appliance plug directly into
the Clipper and plug the adapter into any
120V AC outlet (fig 1). Use only the cord
provided.
3 The Charging Light on the appliance will
blink green to indicate the Clipper is
charging (fig. 2).
w It will take approximately 1 hour to fully
charge the Clipper for a cordless clipping
time of up to 60 minutes.
4 When the battery is fully charged, the
Charging Light lights up green continuously.
NOTE: After 30 minutes the Charging Light
goes out to save energy.
5 Disconnect the cord and unplug from
electrical outlet.
Corded Hair Clipping
w Clipper does not recharge during corded
clipping.
1 Connect cord provided to clipper and plug
clipper into electrical outlet (fig. 1).
2 If battery is completely empty, wait a few
minutes before switching clipper ON.
3 Slide ON/OFF switch ON to begin clipping.
4 Turn clipper OFF and unplug.
Cordless Hair Clipping
1 Charge according to directions. Unplug
Clipper from outlet and remove cord.
2 Slide ON/OFF switch ON to begin clipping.
3 If the charge runs low while clipping, the
green Charging Light will turn orange.
4 If the charge runs out while clipping, connect
cord provided to Clipper and outlet. Wait
a few seconds and then turn Clipper ON to
continue clipping.
Hair Clipping
w Use this Clipper for its intended household
use as described in this manual.
w Make sure that the appliance is fully charged
before you start clipping hair.
w Before you start clipping, make sure that the
head of the person whose hair you are cutting
is at the same level as your chest so that all
parts of his/her head are clearly visible and
within easy reach.
w Only use the appliance on clean, dry hair.
w Do not use on freshly washed hair.
w Before you begin, comb the hair in the direction
of growth (fig. 3).
w To achieve optimal clipping results, always move
the appliance slowly through the hair against
the direction of hair growth.
Clipping with small or large comb
1 Be certain the Clipper is in the OFF position.
2 Select the comb attachment. The table shows
the remaining hair length after clipping at the
different settings of the small or large comb.
3 Slide the selected comb into the guiding
grooves on both sides of Clipper and push
until you hear it ‘click’ into place (fig. 4).
4 Turn the Zoom Wheel Hair Length Setting
Selector to the desired setting (fig. 5). See
Table 1 for settings.
5 The selected setting number will appear in
the Hair Length Settings Window on the
Clipper.
When you are clipping for the first time, start
at the maximum clipping length setting (#6.5
on small comb or #13 on large comb) to
familiarize yourself with the appliance and prevent
accidentally trimming hairs too short. As you
become familiar with the settings, adjust the Zoom
Wheel Hair Length Setting Selector to desired
trimming length.
6 Make sure that the flat part of the comb is
always in full contact with the scalp to obtain
an even result (fig. 6).
7 Since all hairs do not grow in the same
direction, move the appliance slowly over the
crown from different directions (i.e. upwards,
downwards and across) to achieve an even
result (fig. 7).
8 Always move the appliance against the
direction of hair growth.
A Stainless Steel Cutter Blades
B On/Off Button
C Zoom Wheel Hair Length Setting Selector
D Charging Light
E Socket for Appliance Plug
F Hair Length Settings Window
G Small Comb
H Large Comb
I Hair Length Settings
J Cleaning Brush
K Adapter
L Appliance Plug
Full Two-Year Warranty
45-Day Money-Back Guarantee
This symbol indicates that
the Clipper can be rinsed
under running tap water.
Put It To The Test
Like many new products, your Philips Norelco Hair
Clipper may take a little getting used to. If you are
using an electric Clipper for the first time, or if
you’ve been using a different brand, take the time
to acquaint yourself with your new Hair Clipper.
Your Hair Clipper features an extra strong motor
and stainless steel cutter blades to comfortably clip
even the toughest hair.
Throw your scissors away and put your new
Hair Clipper to the test. We guarantee precise,
professional results or Philips Norelco will
refund you the full purchase price as long as the
request is received within 45 days of purchase.
To Charge/Recharge
w Fully charge Clipper before using for the first
time or after non-use for a long period of time.
w Charging, recharging, or using Clipper at
temperatures below 40˚F or higher than 95˚F
adversely affects lifespan of the battery.
w Do not charge/recharge or use Clipper corded
until fully dry.
9 Make overlapping passes over the head to
ensure that all hair that should be cut has
been cut.
10 For best results with curly, sparse or long
hair, use a styling comb to guide the hair
towards the Clipper.
11 Turn the Clipper off regularly during clipping
and remove the hair comb to blow and/or
shake out hair that has accumulated.
w TIP: Write down the settings you have used to
create a certain hairstyle as a reminder for future
clipping sessions.
Contouring without a comb
w Use the Clipper without a comb to clip hair
very close to the skin (3/64 in./1mm) or to
contour the neckline and area around the ears.
1 Remove the hair comb by pulling it off the
Clipper (fig. 8).
Be careful when you are clipping without comb
attachment as when the Clipper is turned on it
will remove every hair it touches.
2 To contour the hairline around the ears,
comb the hair ends over the ears.
3 Tilt the Clipper in such a way that only
one edge of the cutter blades touches the
hair ends when you shape the contours
around the ears (fig. 9).
Only cut the hair ends. The hairline should be
close to the ear.
4 To contour the nape of the neck or
sideburns, turn the Clipper and hold it with
the cutter blades pointing downwards
(fig. 10).
5 Move the Clipper slowly and smoothly
following the natural hairline.
Cleaning
w Clean the attachments after each use.
w Always switch Clipper OFF, unplug and remove
power supply cord from Clipper before
cleaning.
w Do not use compressed air, abrasive cleaning
agents, scourers or aggessive liquids such as
gas, acetone or ethereal oils to clean the
Clipper and attachments.
w Never clean, replace or remove Clipper
attachments with motor ON.
w Do not apply pressure to cutters.
w Do not touch cutters with hard objects as this
may damage them.
w Use a soft, dry cloth to clean Clipper handle.
During Use:
w If cut hairs have accumulated in the comb
area, remove hairs by shaking, blowing or
using cleaning brush provided. Remember to
adjust the clipping length back to your selected
setting when you replace the comb on Clipper.
After Each Use:
1 Make sure the Clipper is switched OFF
and disconnected from the electrical outlet.
2 Remove any comb and rinse it under warm
water.
3 Push the center top end of the cutter
blade upwards with your thumb until it
opens (fig. 11).
4 Clean the appliance under warm water
to flush out the cut hair that has accumulated
in the clipping attachment (fig. 12).
IMPORTANT
SAFETY
INSTRUCTIONS
When using an electrical appliance, basic safety
precautions should always be followed, including
the following:
Read all instructions before using this
appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a clipper that has fallen into
water. Unplug immediately.
2. Use clipper only in dry condition. Do not use
while bathing or in a shower.
3. Do not submerge clipper in water.
4. Do not place or store clipper where it can
fall or be pulled into a tub or sink. Do not
place in or drop into water or other liquid.
5. Always unplug this clipper from the electrical
outlet immediately after using, except when
clipper is (re)charging.
6. Unplug and remove power supply cord from
clipper before cleaning.
7. The batteries used in this device may present
a fire or chemical burn hazard if mistreated.
Do not disassemble, heat above 100°C
(212°F) or incinerate.
WARNING
To reduce the risk of burns, fire, electric
shock or injury to persons:
1. Close supervision is necessary when
this appliance is used by, on, or near children
or invalids.
2. Use this clipper for its intended household
use as described in this manual. Do not use
attachments not recommended by Philips
Electronics North America Corporation.
3. Never operate this clipper if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped, damaged,
or dropped into water. For assistance, call
1-800-243-3050.
4. Clipper can be rinsed under running tap
water. Do not operate clipper until fully
dry.
5. Keep the clipper, cord and any attachments
away from heated surfaces.
6. Never drop or insert any object into any
opening.
7. Do not operate, charge or plug in clipper
outdoors or where aerosol (spray) products
are being used or where oxygen is being
administered.
8. Always check cutters, cutting unit and combs
before using the clipper. Do not use the
clipper if cutters, cutting unit or combs are
damaged, as injury may occur.
9. Always attach plug to clipper first, then to
outlet. To disconnect, turn on/off switch to
“OFF” position, then remove plug from
outlet.
10. To prevent possible damage to the cord, do
not wrap cord around the clipper.
11. Never put clipper in direct sunlight or store
at a temperature above 140°F.
12. This clipper is for use on human hair only.
Do not use this clipper for any other
purpose.
13. Always store your clipper, attachments and
power plug in a moisture-free area. Make
sure the cord is disconnected from the
clipper.
14. Only use the power plug supplied with the
appliance.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains
a transformer. Do not cut off the power
plug to replace it with another plug as this
will cause a hazardous condition.
IMPORTANT: YOUR CLIPPER
CONTAINS A LITHIUM-ION
RECHARGEABLE BATTERY.
See Battery Removal Instructions.
Registration
Congratulations on your purchase and welcome
to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.philips.com/norelco
Register your product and get support at
www.philips.com/norelco
Full Two-Year Warranty
Philips Electronics North America Corporation warrants each new
Philips Norelco product, Model QC5340 (except cutter and combs)
against defects in materials or workmanship for a period of two years
from the date of purchase, and agrees to repair or replace any defective
product without charge.
IMPORTANT: This warranty does not cover damage resulting from
accident, misuse or abuse, lack of reasonable care, the affixing of any
attachment not provided with the product or loss of parts or subjecting
the product to any but the specific voltage.* Use of unauthorized
replacement parts will void this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY
A NON-AUTHORIZED REPAIR SERVICE AND WILL NOT
REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM
WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED
REPAIR SERVICE.
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/
norelco or call 1-800-243-3050 for assistance. It is suggested that for
your protection you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipment is not covered by
this warranty. NOTE: No other warranty, written or oral, is authorized
by Philips Electronics North America Corporation. This warranty gives
you specific legal rights, and you may also have other rights which vary
from state to state. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above exclusion and
limitations may not apply to you.
*Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A Division of Philips Electronics North America Corporation
P.O. Box 10313, Stamford, CT 06904
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.
Norelco is a Registered Trademark of Philips Electronics
North America Corporation.
PHILIPS is a Registered Trademark of Koninklijke Philips Electronics N.V.
© 2011 Philips Electronics North America Corporation. All Rights Reserved.
E
A
B
C
1 1.5 2 3 3.5 4 5 5.5 6 6.5
D
1 1.5 2 3 3.5 4 5 5.5 6 6.5
7 8 8.5 9 10 10.5 11 12 12.5 13
J
I
F
H G
K
L
Features
13
1 2 3
1 1.5 2 3 3.5 4 5 5.5 6 6.5
4 5 6
7
3
3.5
4
8 9
10 11 12
4222 002 8206 1
QC5340
Rechargeable
Cordless/Cord
Hair Clipper
Pro
5 Let the appliance and clipping attachment air
dry completely.
This Clipper has no other user-serviceable parts.
For assistance call 1-800-243-3050.
Assistance
For assistance, visit our website:
www.philips.com/support
or call toll free: 1-800-243-3050
Information is available 24 hours a day,
7 days a week.
Storage
w Be sure Clipper is turned OFF. Remove cord
from outlet and Clipper before storing in a
safe, dry location where it will not be crushed,
banged, or subject to damage.
w Do not wrap cord around Clipper when
storing.
w Store cord in a safe location where it will not
be cut or damaged.
w Do not place or store Clipper where
it can fall or be pulled into a tub or sink, water
or other liquid while plugged in.
Battery Removal
w This Philips Norelco Clipper contains a
rechargeable Lithium-Ion battery
which must be disposed of properly (fig. 13).
w Battery may only be removed when
Clipper is to be discarded.
w For assistance, visit our website:
www.philips.com/support or
call toll free: 1-800-243-3050
1 Unplug electrical cord from outlet and
Clipper before dismantling Clipper.
2 Allow Clipper to run until the battery is
empty/depleted.
3 Turn Clipper OFF.
4 Remove any comb and clipping attachment
from the handle.
5 Check if there are any screws in the back or
front of the appliance. If so, remove them.
6 Remove the back and/or front panel of the
appliance with a screwdriver. If necessary,
also remove additional screws and/or parts
until you see the printed circuit board with
the rechargeable batteries.
7 If necessary, cut the wires to separate the
printed circuit board and the rechargeable
batteries from the appliance.
Be careful, the battery strips and housing parts are
very sharp.
8 Do not attempt to replace battery. Insulate
battery ends by covering with tape and/or
place battery in a small plastic bag.
9 Discard your Clipper. Do not attempt to
plug electrical cord into the outlet or
recharge the Clipper after the battery has
been removed.
10 Contact your local town or city officials
for battery disposal information or call
1-800-8-BATTERY or www.rbrc.com for
battery drop-off locations.
Table 1. Small and Large Combs
Remaining
Hair Length
Inches MM
Large
Comb
Barber
Setting
#7
#8
#8.5
#9
#10
#10.5
#11
#12
#12.5
#13
Small
Comb
Barber
Setting
#1
#1.5
#2
#3
#3.5
#4
#5
#5.5
#6
#6.5
1/8
3/16
9/32
3/8
7/16
1/2
5/8
11/16
3/4
13/16
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Remaining
Hair Length
Inches MM
7/8
1
1 1/16
1 1/8
1 1/4
1 5/16
1 3/8
1 1/2
1 5/8
1 11/16
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
11_QC5340.indd 1 1/20/11 11:06 AM