Liebherr KP 4220 Comfort - Manual (Page 8)

The packaging is made of recyclable materials:
- corrugated board/cardboard
- expanded polystyrene parts
- polythene bags and sheets
- polypropylene straps
- nailed wooden frame with polyethylene panel*
u Take the packaging material to an official collecting point.
4.6 Connecting the appliance
NOTICE
Risk of damage to the electronic control system!
u Do not use stand-alone inverters (conversion of d.c. to a.c./
three-phase) or energy saving plugs.
WARNING
Fire and overheating hazard!
u Do not use extension cables or multiple socket outlets.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see Appliance at a glance).
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emergency. It
must be outside the area of the rear of the appliance.
u Check the electrical connection.
u Plug in the power plug.
4.7 Switching on the appliance
u Press On/Off button Fig. 3 (1) .
w The appliance is switched on. The temperature display indi-
cates the set temperature.
w If all LEDs in the temperature display light up, demo mode is
activated. Please contact the after sales service.
5 Control
5.1 Food refrigeration
Note
The energy consumption increases and the cooling perform-
ance decreases if the ventilation is inadequate.
u Always keep the air slits of the fan free.
u Store perishable food such as ready-to-serve dishes, meat
products and sausages in the coldest zone. Place butter
and preserves in the upper area and in the door (see Appli-
ance at a glance).
u Use recyclable plastic, metal, aluminium and glass
containers and cling film for wrapping.
u Use the front area of the refrigerator compartment floor only
for briefly putting down cooled products, e.g. when rear-
ranging and sorting. However do not leave cooled products
there otherwise they may be pushed back or tipped over
when the door is closed.
u Do not store food too close together to enable good air
circulation.
u To safeguard bottles from tipping over: move the bottle
holder.
5.2 Setting the temperature
The temperature depends on the following factors:
- the door opening frequency
- the room temperature at the site where the appliance is
installed
- the type, temperature and quantity of frozen food
Temperature setting to be recommended: 5 °C
The temperature can be changed continuously. Once the 1 °C
setting is reached, it starts again with 9 °C.
u To access temperature adjustment: press the setting button
Fig. 3 (2) once.
w The LED of the current temperature flashes in the tempera-
ture display.
u Press the setting button Fig. 3 (2) the number of times
needed until the required temperature shines in the LED
display.
Note
u Long pressing of the setting button sets a slightly colder
value within a small temperature range (e.g.: between 5 °C
and 7 °C). The LED of the next lower temperature range
then shines in the temperature display.
5.3 SuperCool
With SuperCool you switch to the highest cooling
performance to reach lower cooling temperatures.
Use SuperCool, to rapidly cool large amounts of
food.
When SuperCool is activated, the fan* may run. The appliance
operates with maximum cooling performance, which means
that the noise of the refrigeration unit may be temporarily
louder.
The SuperCool function uses slightly more energy.
5.3.1 Cooling with SuperCool
u Briefly press SuperCool button Fig. 3 (4) .
w The SuperCool button Fig. 3 (4) lights up.
w The cooling temperature drops to the coldest value.
SuperCool is activated.
w SuperCool is automatically deactivated after 6 to12 hours
The appliance continues to operate in the energy-saving,
normal mode.
5.3.2 To prematurely deactivate SuperCool
u Briefly press SuperCool button Fig. 3 (4) .
w The SuperCool button Fig. 3 (4) goes out.
w SuperCool is deactivated.
5.4 Fan
With the fan you can rapidly cool large quantities of
fresh food or achieve a relatively even distribution of
temperature across all the storage levels.
The forced-air cooling is to be recommended:
- at high room temperature (above33 °C )
- at high humidity
The forced-air cooling uses slightly more energy. To save
energy, the fan switches off automatically when the door is
open.
5.4.1 Switching on the fan
u Briefly press the fan button Fig. 3 (5) .
w The fan button shines.
Control
8 * Depending on model and options