Liebherr KBes 4260 Premium BioFresh - Manual (Page 7)

Fig. 5
u Lift out the bearing pin Fig. 5 (22) together with washer
Fig. 5 (23) and adjustable-height foot Fig. 5 (24) .
u Lift off the stopper Fig. 5 (21) .
u Unscrew Fig. 5 (26) the turn hinge Fig. 5 (25) .
u Unscrew Fig. 5 (29) the bearing element Fig. 5 (28) , transfer
it to the opposite location hole of the turn hinge and screw it
firmly into place.
u Carefully lift off the cover on the handle side Fig. 5 (27) and
transfer it to the opposite side.
u Screw the turn hinge Fig. 5 (25) firmly into place on the new
hinge side, possibly using a cordless screwdriver (with
4 Nm).
u Re-insert the stopper Fig. 5 (21) into the other hole.
u Re-insert the bearing pin Fig. 5 (22) together with the
washer and adjustable-height foot. In so doing, pay attention
that the locating lug points backwards
4.3.4 Changing the bearing parts
For appliances with height adjustment
Fig. 6
u Using the accompanying Allen key, unscrew the threaded
pin Fig. 6 (40) by about 1 turn.
u Turn and lift out the bearing pin Fig. 6 (22) together with the
washer Fig. 6 (23) and adjustable-height foot Fig. 6 (24) .
u Lift out the stopper Fig. 6 (21) .
u Unscrew Fig. 6 (26) the turn hinge Fig. 6 (25) .
u Fully unscrew the threaded pin Fig. 6 (40) and screw it in on
the opposite side, at the turn hinge, until it is flush outside
with the turn hinge.
u Unscrew Fig. 6 (29) the bearing element Fig. 6 (28) transfer it
to the opposite location hole of the turn hinge and screw it
firmly into place.
u Re-insert the stopper Fig. 6 (21) into the other hole.
u Carefully lift off the cover on the handle side Fig. 6 (27) and
transfer it to the opposite side.
u Screw the turn hinge Fig. 6 (25) firmly into place on the new
hinge side, possibly using a cordless screwdriver (with
4 Nm).
u Re-insert the bearing pin Fig. 6 (22) together with the
washer and adjustable-height foot.
u Tighten the threaded pin Fig. 6 (40) .
4.3.5 Transferring the handle
u Transfer the spring clamp
Fig. 7 (31) : Depress the
latch nose and pull the
spring clamp off over it.
u Slide the spring clamp
into place on the new
hinge side until it clicks
into place.
Fig. 7
Fig. 8
u Lift the stopper Fig. 8 (33) out of the door bearing bush and
transfer it.
u Dismantle the door handle Fig. 8 (32) , stoppers Fig. 8 (33)
and pressure plates* Fig. 8 (34) and transfer to the opposite
side.
u When fitting the pressure plates on the opposite side, make
sure they snap properly into place.*
4.3.6 Fitting the door
u Place the door from above onto the lower bearing pin
Fig. 6 (22) .
u Close the door.
u Insert the upper turn hinge Fig. 4 (12) in the door on the new
hinge side.
u Screw the upper turn hinge Fig. 4 (12) firmly into place (with
4 Nm)(2x Torx® 25) Fig. 4 (13) . Possibly make preliminary
holes with a bradawl or use a cordless screwdriver.
u Snap the cover Fig. 4 (10) and cover Fig. 4 (11) into place at
the opposite side.
4.3.7 Aligning the door
u Align the door to the appliance housing by way of the two
oblong holes in the bottom turn hinge Fig. 6 (25) . To do so,
unscrew the middle screw.
Putting into operation
* Depending on model and options 7