Liebherr TX 1021 Comfort - Manual (Page 8)

u Read the appliance
designation Fig. 7 (1) ,
service No. Fig. 7 (2)
and serial No.
Fig. 7 (3) off the type
plate located inside
the appliance on the
left-hand side.
Fig. 7
u Notify the customer service, specifying the fault, appliance
designation Fig. 7 (1) , service No. Fig. 7 (2) and serial No.
Fig. 7 (3) .
w This will help us to provide you with a faster and more accu-
rate service.
u Keep the appliance closed until the customer service
arrives.
w The food will stay cool longer.
u Pull out the mains plug (not by pulling the connecting cable)
or switch off the fuse.
7 Malfunction
Your appliance is designed and manufactured for a long life
span and reliable operation. If a malfunction nonetheless
occurs during operation, check whether it is due to a handling
error. In this case you will have to be charged for the costs
incurred, even during the warranty period. You may be able to
rectify the following faults yourself:
Appliance does not work.
→ The appliance is not switched on.
u Switch on the appliance.
→ The power plug is not properly inserted in the wall socket.
u Check power plug.
→ The fuse of the wall socket is not in order.
u Check fuse.
The compressor runs for a long time.
→ The compressor switches to a low speed when little cold is
needed. Although the running time is increased as a result,
energy is saved.
u This is normal in energy-saving models.
A LED on the bottom rear of the appliance (at the
compressor) flashes regularly every 15 seconds*.
→ The inverter is equipped with a diagnostic LED.
u The flashing is normal.
Excessive noise.
→ Due to the various speed steps, speed-regulated*
compressors can generate different running noises.
u The sound is normal.
A bubbling and gurgling noise.
→ This noise comes from the refrigerant flowing in the refriger-
ation circuit.
u The sound is normal.
A quiet clicking noise.
→ The noise is produced whenever the refrigeration unit
(motor) automatically switches on or off.
u The sound is normal.
A hum. It is briefly a little louder when the refrigeration
unit (the motor) switches on.
→ The refrigeration increases automatically when fresh food
has just been placed in the appliance or the door has been
left open for a while.
u The sound is normal.
→ The ambient temperature is too high.
u Solution: (see 1.2)
Vibratory noise.
→ The appliance is not fixed to the ground. The running of the
cooling unit therefore makes objects and adjacent furniture
vibrate.
u Adjust appliance via the height-adjustable feet.
u Move bottles and containers apart.
The outer surfaces of the appliance are warm*.
→ The heat of the refrigeration circuit is used to prevent
condensate from forming.
u This is normal.
The temperature is not cold enough.
→ The door of the appliance is not properly closed.
u Close the door of the appliance.
→ Insufficient ventilation.
u Clear ventilation grilles.
→ The ambient temperature is too high.
u Solution: (see 1.2) .
→ The appliance was opened too frequently or for too long.
u Wait to see whether the appliance reaches the required
temperature by itself. If not, please contact the after sales
service (see Maintenance).
→ The appliance is too close to a source of heat (stove, heater
etc).
u Change the position of the appliance or the source of heat.
The interior light is not on.
→ The appliance is not switched on.
u Switch on the appliance.
→ The bulb is faulty.
u Change the bulb (see Maintenance).
8 Decommissioning
8.1 Switching off the appliance
u Turn temperature control Fig. 3 (1) to 0.
8.2 Taking the appliance out of service
u Empty the appliance.
u Pull out the power plug.
u Clean the appliance (see 6.2) .
u Leave the door open to prevent odour.
9 Disposing of the appliance
The appliance contains some reusable materials
and should be disposed of properly - not simply
with unsorted household refuse. Appliances which
are no longer needed must be disposed of in a
professional and appropriate way, in accordance
with the current local regulations and laws.
When disposing of the appliance, ensure that the refrigeration
circuit is not damaged to prevent uncontrolled escape of the
refrigerant it contains (data on type plate) and oil.
u Disable the appliance.
u Pull out the plug.
u Cut through the connecting cable.
Malfunction
8 * Depending on model and options