Liebherr LTM 1160-5.1 - Manual (Page 2)

11 2 LTM 1160-5.1 LTM 1160-5.1
600
3496 4488
7984
3136 4823
R = 5100
R = 10600
R = 12300
3000 5000 5310 7500
R = 4220
R = 11800
21°
12 t 12 t 12 t 12 t 12 t 16.00 R 25
4000
12346
14740
26°
15020
2394
Compact, maneuverable
and weight-optimized The LICCON test system
• This test system assists the servicing personnel to localize
faults in the crane sensory system quickly without the need
for measuring instruments
• Service work starts at the display screen:
troubleshooting takes only a few moments
• Faults are indicated by codes and descriptions
on the display screen
• Convenient interactive functions permit observation of all
inputs and outputs to and from the entire system; they can
be displayed in different forms on the display screen even
during crane operation. The system also visualizes the
position of the system’s individual sensors and actuators
and their functions
The LICCON work area
limiting system
• This reduces the crane operator’s workload, by monitoring
the work area limits, especially in situations where the
handling of loads requires close attention. Work areas can
be restricted to allow for buildings, bridges, roofs, high-
tension power lines, pipelines or adjacent cranes. The
automatic work area limiting system (optional) can easily be
programmed. Four different limiting functions are practicable:
• Height limit for pulley head
• Radius limit
• Slewing angle limit
• Border limits
The LICCON work planner
• The LICCON work planner consists of a software program
on CD for the planning, simulation and documentation of
crane applications on the display screen (optional)
• The 2D planner program permits buildings to be drawn, text
entered and a true to scale crane model represented, including
all movements within a simulated construction site
• The work planner creates greater clarity when preparing
offers, facilitates the briefing of crane operators and can be
run on a laptop at the construction site
• Powerful, 6-cylinder Liebherr Type D846 A7 turbocharged
diesel engine, 370 kW/503 hp, exhaust emissions comply
with 97/68/EC Stage 3 and EPA/CARB Tier 3; robust and
reliable, with modern, electronic engine management
• ZF AS-TRONIC automated manual shift gearbox; ZF Intarder
fitted directly to gearbox; 12 forward and 2 reverse gears,
automated gear shift, high number of gear ratios helps to
reduce fuel consumption
• Robust 2-stage transfer box with lockable differential,
creep speed 0.78 km/h
• Drive 10 x 6: axles 2, 4 and 5 driven
• Drive 10 x 8 (optional): axles 2, 4 and 5 driven,
axle 1 can be engaged for off-road travel
• Robust, low-maintenance weight-optimized axles, special
arrangement of the maintenance-free suspension control
arms for excellent directional and lateral stability, steel and
rubber locating bushings
• Maintenance-free propeller shafts; easy and quick fitting
due to 70° degree cross-splines
• “Niveaumatik” hydropneumatic suspension, program-
controlled for raising crane onto outrigger supports, crane
travel with equipment and on-road crane travel; suspension
travel +150/-150 mm
• Maintenance-free suspension rams free from lateral forces,
piston rods protected against damage by plastic tubes
• Retarders:
Exhaust brake with additional Liebherr brake system (ZBS),
Intarder integrated in gearbox, Telma eddy current brake
(optional)
• Service brake:
All axles fitted with air-operated disc brakes, high braking
performance, extended maintenance intervals, rapid brake
pad renewal
Modern drive concept
• Overall length 15.02 m, chassis length 12.35 m
• Large overhang angle of up to 26°
• Minimum turning-circle radius 10.6 m with all-wheel steering
• Rear ballast radius only 4.22 m
• 60 t gross weight, incl. 6.5 t ballast, 10 x 8 driveline,
16-inch tires, 26 t hook block (axle load 5 x 12 t)
• 3 optional tire sizes
14.00 R 25 (vehicle width 3 m)
16.00 R 25 (vehicle width 3 m)
20.5 R 25 (vehicle width 3.1 m)