Philips HAIRCLIPPER Series 3000 Tondeuse à cheveux - Manual (Page 2)

1 Comb your hair with a styling comb in the
direction of hair growth. (Fig. 3)
2 Slide the hair clipping comb into the guiding
grooves of the appliance (‘click’) (Fig. 4).
Make sure that the arms of the comb have been
properly slid into the grooves on both sides.
3 Press the length setting selector (1) and then
move the hair clipping comb up or down (2)
to set the desired length setting (Fig. 5).
, The corresponding hair length is visible on
the side of the comb.
length settings
With the hair clipping comb attached, the appliance
can cut hair to 10 different lengths:
Hair lengths in mm Hair lengths in inches
3 1/8
5 3/16
7 9/32
9 3/8
11 7/16
13 1/2
15 5/8
17 21/32
19 3/4
21 7/8
4 Slide the on/off slide upwards to switch on
the appliance (Fig. 6).
5 Place the hair clipping comb on the scalp and
move the appliance through the hair slowly.
Tips
- Start clipping at the highest length setting of
the hair clipping comb and reduce the length
setting gradually.
- Write down the length settings you have used
to create a certain hairstyle as a reminder for
future clipping sessions.
- To clip in the most effective way, move the
appliance against the direction of hair growth.
- Since hair grows in different directions, you need
to move the appliance in different directions as
well (upward, downward or across) (Fig. 7).
- Make overlapping passes over the head to
ensure that the appliance catches all the hairs
that need to be cut.
- Make sure that the flat part of the hair clipping
comb is fully in contact with the scalp to obtain
an even clipping result.
- To achieve a good result with curly, sparse or
long hair, you can use a styling comb to guide
the hair towards the appliance.
- Regularly remove cut hair from the hair
clipping comb. If a lot of hair has accumulated
in the comb, remove it from the appliance and
blow and/or shake the hair out of it.
Clipping without hair clipping comb
You can use the appliance without hair clipping
comb to clip your hair very close to the skin, to a
length of 1mm (1/32 in) to contour the neckline
and the area around the ears.
1 To remove the hair clipping comb, press
the length setting selector (1), move the
comb upwards and then pull it off the
appliance (2). (Fig. 8)
2 Comb the hair ends over the ears before you
start to contour the hairline.
3 Slide the on/off slide upwards to switch on
the appliance (Fig. 6).
4 Tilt the appliance in such a way that only one
edge of the cutting element touches the hair
ends. (Fig. 9)
5 Only cut the hair ends. The hairline has to be
close to the ear.
6 To contour the neckline and the sideburns,
turn the appliance and make downward
strokes (Fig. 10).
7 Move the appliance slowly and
smoothly. Follow the natural hairline.
Cleaning
Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids such as
alcohol, petrol or acetone to clean the appliance.
Only clean the appliance and the adapter with the
cleaning brush supplied.
Do not use any sharp objects to clean the appliance.
Clean the appliance after every use.
1 Make sure the appliance is switched off and
disconnected from the mains.
2 To remove the comb, press the length setting
selector (1), move the comb upwards and
then pull it off the appliance (2). (Fig. 8)
3 Push the middle part of the cutting
unit upwards with your thumb until it
opens (Fig. 11).
4 Clean the cutting unit with the cleaning brush
supplied (Fig. 12).
5 Clean the inside of the appliance with the
cleaning brush supplied (Fig. 13).
6 Clean the hair clipping comb with the
cleaning brush supplied.
Note: The appliance does not need any lubrication.
Replacement
To buy accessories or spare parts, visit
www.shop.philips.com/service or go to your
Philips dealer. You can also contact the Philips
Consumer Care Centre in your country (see the
worldwide guarantee leaflet for contact details).
The cutting unit, the adapter and the hair
clipping comb are replaceable.
Replacing the cutting unit
Replace the cutting unit if it is damaged or worn.
Only replace the cutting unit with an original Philips
cutting unit.
1 Push the middle part of the cutting unit
upwards with your thumb until it opens and
then pull it off the appliance (Fig. 14).
2 Place the lug of the new cutting unit in the
slot and push the cutting unit onto the
appliance (‘click’) (Fig. 15).
Environment
- Do not throw away the appliance with the
normal household waste at the end of its life,
but hand it in at an official collection point for
recycling. By doing this, you help to preserve
the environment (Fig. 16).
- The built-in rechargeable batteries contain
substances that may pollute the environment.
Always remove the batteries before you
discard and hand in the appliance at an official
collection point. Dispose of the batteries at
an official collection point for batteries. If you
have trouble removing the batteries, you can
also take the appliance to a Philips service
centre. The staff of this centre will remove the
batteries for you and will dispose of them in an
environmentally safe way (Fig. 17).
Removing the rechargeable batteries
Only remove the rechargeable batteries when
you discard the appliance. Make sure the batteries
are completely empty when you remove them.
Do not connect the appliance to the mains again
after you have removed the rechargeable batteries.
1 Disconnect the appliance from the mains and
let the appliance run until the motor stops.
2 Remove the hair clipping and the cutting unit.
3 Remove the 2 screws at the back of the
appliance with a screwdriver (Fig. 18).
4 Pull the back panel off the appliance (Fig. 19).
5 Remove the 6 screws on the inside of the
appliance with a screwdriver (Fig. 20).
6 Separate the power unit from the front
panel. (Fig. 21)
7 Cut the wires close to the batteries and then
remove the batteries (Fig. 22).
guarantee and support
If you need information or support, please visit
www.philips.com/support or read the separate
worldwide guarantee leaflet.
DEUTsCh
Einführung
Herzlichen Glückwunsch zu Ihrem Kauf und
willkommen bei Philips! Um die Unterstützung von
Philips optimal nutzen zu können, registrieren Sie Ihr
Produkt bitte unter www.philips.com/welcome.
Allgemeine Beschreibung (Abb. 1)
1 Haarschneidekammaufsatz
2 Schnittlängenregler
3 Schneideelement
4 Ein-/Ausschalter
5 Ladeanzeige (CHARGE)
6 Buchse für Gerätestecker
7 Gerätestecker
8 Adapter
9 Reinigungsbürste
Wichtig
Lesen Sie diese Bedienungsanleitung vor dem
Gebrauch des Geräts aufmerksam durch, und
bewahren Sie sie für eine spätere Verwendung auf.
gefahr
- Achten Sie darauf, dass der Adapter nicht nass wird.
Warnhinweis
- Prüfen Sie vor Inbetriebnahme, ob die
Spannungsangabe am Adapter und am Gerät
mit der örtlichen Netzspannung übereinstimmt.
- Der Adapter enthält einen Transformator.
Ersetzen Sie den Adapter keinesfalls
durch einen anderen Stecker, da dies eine
Gefährdungssituation darstellt.