Philips 40PFL4907-F7 - Manual (Page 42)

English
42
IPconfiguration
In following cases, select IP configuration to set each setting as
necessary.
– When connection test failed with the setting of Connection test.
– When instructed by your Internet service provider to make specific
settings in accordance with your network environment.
3
Use ▲▼ to select IP configuration, then press OK.
4
Use ▲▼ to select a setting, then press OK.
Network selection IP setting mode Manual
Wireless network setting IP address 192.168.11.3
IP configuration Subnet mask 255.255.255.0
Proxy configuration Default gateway 192.168.11.1
Primary DNS 192.168.11.1
Secondary DNS 0.0.0.0
MAC address 00:12:0E:10:09:15
IP setting mode
Auto Sets the IP setting automatically.
Manual Sets the IP setting manually.
IP address * 1, 3
A set of numbers which are assigned to
devices participating in a computer network.
Subnet mask * 1, 3
A mask which is used to determine what
subnet an IP address belongs to.
Default gateway * 1, 3
IP address of the network device (such as
router) which provides Internet access.
DNS
setting mode
Auto Sets the DNS setting automatically.
Manual Sets the DNS setting manually.
Primary DNS * 2, 3
A server which handles the name and IP
address over the Internet.
Secondary DNS * 2, 3
A server which handles the name and IP
address over the Internet.
MAC address
An address which recognizes the devices
connecting to the network. It is also called
Hardware Address.
*1 Items can be selected only when IP setting mode is set to Manual.
*2 Items can be selected only when DNS setting mode is set to Manual.
*3 Use ▲▼ or the NUMBER buttons to input numbers. When you use
▲▼ to input numbers, then press OK or input the triple digits by using
the NUMBER buttons, the cursor moves to the next entry field. When you
use ▲▼ to input numbers, then press OK or input the triple digits by using
the NUMBER buttons at the rightmost entry field, numbers will be stored
and go back to the previous menu.
Note
• The range of input numbers is between 0 and 255.
• If you enter a number larger than 255, the number will automatically be 255.
• The manually entered number will be saved even if you change the setting to Auto.
• If you want to enter 1 or 2 digit number in one cell, press OK to move on to the next
cell.
• If the entered IP address or the default gateway or primary DNS number is same as
the default setting, IP address setting will be set to Auto. (The manually entered number
will be saved).
• When IP address setting is set to Manual, the setting of DNS setting will automatically
be Manual and when IP address setting is set to Auto, you can set either Auto or
Manual for DNS setting.
Proxyconfiguration
3
Use ▲▼ to select Proxy configuration, then press OK.
4
Use ▲▼ to select a setting, then press OK.
Network selection Proxy setting Do not use
Wireless network setting
IP configuration
Proxy configuration
• Do not use is selected for default settings.
• If you need to change the proxy setting as instructed by your
Internet service provider to set the designated proxy address
and port, select Use.
Proxy setting
Do not use Not use the proxy server.
Use Uses the proxy server.
Proxy address *
Selects the number or word by using
▲▼◄►, then press OK.
Proxy port *
Use ▲▼ or the NUMBER buttons to input
numbers.
* Items can be selected only when Proxy setting is set to Use.
Note
• The range of input numbers for the port number is between 0 and 65535.
(If you enter a number larger than 65535, it will be regarded as 65535.)
• For proxy port, the selected ports may be blocked and not be able to use depending
on your network environment.
• If the proxy address is entered with blank only, proxy server setting will be set to
Do not use.
Connection test
Perform the following steps to test your Internet connection after you
have connected an Ethernet cable or entered network settings such as
IP address, DNS settings, etc. manually.
2
Use ▲▼ to select Connection test, then press OK.
3
Press OK to select Start now.
• Connection test will start automatically and the test result will
appear right after the connection test finishes.
Testing… The test is in progress.
Pass Connection test is successfully completed.
Fail Connection test failed. Check the connection settings.
4
Press OK to go to the list of network status confirmation screen.
Note
• If the connection test passes, you are ready to use Net TV or network upgrade function
using the Internet without making any additional settings.
• If the connection test fails, check if the Ethernet cable is connected to this TV properly
or if you have entered all the required details for the wireless LAN connection properly.
Continued on next page.