Philips QG3360-42 - Manual

3 Tilt the Groomer in such a way that only
one edge of the cutter blades touches the
hairs when you shape the contours around
the ears (fig. 10).
Be careful not to trim too much. The hairline
should be close to the ear.
4 To contour the nape of the neck or
sideburns, turn the Groomer and make
downward strokes (fig. 11).
5 Move the Groomer slowly and smoothly
following the natural hairline.
Trimming your Beard & Moustache
with Beard & Moustache Comb
1 Put the trimmer on Groomer handle (1) and
turn clockwise (2) (fig. 3).
2 Slide the beard & moustache comb into
the guiding grooves on both sides of the
handle (fig. 12).
3 Press the Hair Length Setting Selector (1)
and slide the comb to the desired setting (2)
(fig. 13).
The beard and moustache comb cuts hair to a
length of 3/64-23/32in / 1-18mm.
w If you are trimming for the first time, start
by using the comb at the maximum trimming
length setting (23/32 in/18mm) to prevent
accidentally trimming hairs too short. As you
become familiar with the settings, adjust Hair
Length Setting Selector to desired trimming
length. Selector will “click” into position at each
setting.
4 Turn the Groomer ON (fig. 8).
5 To trim in the most effective way, move
the Groomer against the direction of hair
growth. Make sure the surface of the comb
always stays in contact with the skin.
NOTE: Since all hairs do not grow in the same
direction, you may want to try different trimming
positions (i.e., upwards, downwards, or across).
Practice is best for optimum results.
w If a lot of hair has accumulated in the comb,
remove the comb and blow and/or shake the
hair out of the comb. You can also use the
cleaning brush provided to remove
hair from the comb area.
w REMEMBER: You must reset the hair length
selector back to your desired setting every time
you replace the comb on the appliance.
w The remaining hair length corresponds with
the smallest distance between the cutting
blade and the spot where the comb is in contact
with the skin.
Trimming for 'Stubble' Look
1 Slide the stubble comb into the guiding
grooves on both sides of groomer handle (fig.
14).
The stubble comb cuts hair to a length of 3/64 -
15/32in / 1-12mm.
Beard Trimming Without
Beard & Moustache Comb
Remove comb if you are:
w Defining hair lines
w Trimming nape of neck
w Removing single, unwanted hairs
1 Be certain the Groomer is in the OFF
position.
2 Remove the comb by pressing the Hair
Length Setting Selector (1) and slide the
comb upwards (2). Pull comb off Groomer .
3 Turn the Groomer ON (fig. 8).
4 Make well-controlled movements. Touch the
hair/skin lightly with the Groomer.
Styling/Contouring with Precision
Trimmer
w Use the precision trimmer to cut shapes in
beard hair or scalp hair.
w Be careful when using the precision trimmer as
it removes every hair it touches.
1 Put the precision trimmer on the Groomer
handle (1) and turn clockwise (2) (fig. 3).
2 Make careful and controlled movements with
the precision trimmer.
3 For best results, move the precision trimmer
against the direction of hair growth making
sure it is in full contact with the skin (fig. 16).
TIP: For a perfect finish, use the mini foil shaver
to make edges and lines of your beard style even
smoother (fig. 17).
Cordless Trimming
1 Charge according to directions. Unplug
Groomer from outlet and remove cord.
2 Press ON/OFF button ON to begin trimming.
3 If the battery runs low (approximately 10
minutes of grooming time left) the Battery
Status Indicator will light up orange indicating
Groomer needs to be (re)charged.
4 Connect appliance plug to Groomer. A quick
charge for 5 minutes gives you 5 minutes of
trimming time.
5 If the charge runs out while trimming, simply
connect cord provided to Groomer and
outlet to continue trimming.
Hair Clipping
w Use this Groomer for its intended household
use as described in this manual.
w Make sure that the Groomer is fully charged
before you start clipping.
w Before you start clipping, make sure that the
head of the person whose hair you are cutting
is at the same level as your chest so that all
parts of his/her head are clearly visible and
within easy reach.
w Make sure hair is clean and dry.
w Before you begin, comb the hair in the
direction of growth (fig. 2).
w To achieve optimal clipping results, always move
the appliance slowly through the hair against
the direction of hair growth.
Do not move the Groomer too fast. Make smooth
and gentle movements.
Clipping with hair clipping comb
1 Put the trimmer on Groomer handle
(1) and turn clockwise (2) (fig. 3).
2 Slide the hair clipping comb into the guiding
grooves on both sides of Groomer handle
(fig. 4).
3 Press the Hair Length Setting Selector (1)
and slide the comb to the desired setting (2)
(fig. 5).
The hair clipping comb cuts hair to a length of
1/8 - 25/32in / 3-20mm.
4 The setting selected is shown on the back
of the Groomer.
When you are clipping for the first time, start at
the maximum clipping length setting (25/32in /
20mm) to familiarize yourself with the appliance
and prevent accidentally trimming hairs too short.
As you become familiar with the settings, adjust
the Hair Length Setting Selector to desired trim-
ming length. Selector will ‘click’ into position at
each setting.
5 Turn the Grooomer ON (fig. 6).
6 Make sure that the flat part of the comb is
always in full contact with the scalp to obtain
an even result (fig. 7).
7 Move the appliance slowly over the crown
from different directions to achieve an even
result (fig. 8).
8 Always move the appliance against the
direction of hair growth. Press lightly.
9 Make overlapping passes over the head to
ensure that all hair that should be cut has
been cut.
10 Turn the Groomer off and remove the hair
clipping comb often to blow and/or shake
out hair that has accumulated.
w REMEMBER: You must reset the hair length
selector back to your desired setting every
time you replace the hair clipping comb on the
appliance.
TIP: Write down the settings you have used to create
a certain hairstyle as a reminder for future clipping
sessions.
Contouring without the hair clipping
comb
w Use the Groomer without a comb to clip hair
very close to the skin (3/64in./1mm) or to
contour the neckline and area around the ears.
1 Remove the hair comb by pressing the Hair
Length Setting Selector (1) and slide the
comb upwards (2). Pull comb off Groomer
(fig. 9).
Be careful when you are clipping without comb
attachment as when the Clipper is turned on it
will remove every hair it touches.
2 To contour the hairline around the ears,
comb the hair ends over the ears.
Shaving With Foil Shaver
Use the narrow mini shaver to shave along con-
toured edges to remove any stubble while creating
a smooth, well-defined beard line.
w Before using the mini shaver, always check it
for wear and damage. If the mini shaver shows
signs of wear or damage, do not use it as injury
may occur. Do not use the mini shaver until it
has been replaced.
1 Pre-trim the contours desired with the
trimmer or precision trimmer without a
comb attachment.
2 Put the mini shaver on the Groomer handle.
3 Gently press the mini shaver onto the skin
and shave along contoured edges to remove
any stubble. Do not press too hard (fig. 17).
Grooming Nose/Ear Hair
1 Be certain the Groomer is in the OFF
position.
2 Remove the trimmer by turning counter-
clockwise and pulling it off the Groomer
handle.
3 Put the nose/ear hair trimmer on the
Groomer handle (1) and turn clockwise (2)
(fig. 18).
Trimming Nose Hair
w Make sure nasal passages are clean.
1 Put the nose/ear hair trimmer on the
Groomer handle (1) and turn clockwise (2)
(fig. 18).
2 Turn the Groomer ON and insert the tip
of the attachment into one nostril (fig. 19).
CAUTION: Do Not insert the tip more
than 3/16 in./5mm into your nostril.
3 Slowly move the tip in and out while
turning it around at the same time in order
to remove unwanted hair. For best results,
make sure the side of the tip is firm against
skin. This will reduce the tickling effect that
can occur during trimming of nose hair.
4 Turn off Groomer. Rinse attachment clean
after each use.
Trimming Ear Hair
w Clean outer area of ear and ear canal. Make
sure it is free of wax.
w Nose/ear hair trimmer should be on the
Groomer.
1 Turn the Groomer ON and move the tip
softly around the edge of ear to remove hairs
extending beyond the outer ear (fig. 20).
2 Carefully insert the tip into outer ear canal
(fig. 21).
CAUTION: Do not insert the tip further
than 3/16 in./5mm into the ear as this
could cause damage to the eardrum.
3 Turn off Groomer. Rinse attachment clean
after each use.
Cleaning
w Clean the attachments after each use.
w Always switch Groomer OFF, unplug
and remove power supply cord from
Groomer before cleaning.
w Do not use compressed air, abrasive cleaning
agents, scourers or liquids such as alcohol,
benzene, bleach or acetone to clean the
Groomer and attachments.
w Never clean, replace or remove Groomer
attachments with motor ON.
w Do not apply pressure to cutters.
w Do not touch cutters with hard objects as this
may damage them.
During Use:
w If cut hairs have accumulated in the comb
area, remove hairs by shaking, blowing or using
cleaning brush provided. Remember to adjust
the trimming length back to your selected set-
ting when you replace the comb on Groomer.
After Each Use:
1 Make sure the Groomer is turned OFF
and disconnected from the electrical outlet.
2 Remove any comb or attachment. Rinse
under warm water and allow to air dry
thoroughly.
3 Blow and/or shake out any hair that may
have accumulated in the comb or attachment.
IMPORTANT
SAFETY
INSTRUCTIONS
When using an electric appliance, basic safety
precautions should always be followed, including
the following:
Read all instructions before using this
appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a corded Groomer that has
fallen into water. Unplug immediately.
2. Use Groomer only in dry condition. Do
not use Groomer while bathing or in a
shower.
3. Do not submerge Groomer in water.
4. Do not place or store Groomer where it can
fall or be pulled into a tub or sink. Do not
place or drop Groomer into water or other
liquid while plugged in.
5. Always unplug the Groomer from the
electrical outlet immediately after use,
except when Groomer is (re)charging.
6. Unplug and remove power supply cord from
Groomer before cleaning.
WARNING
To reduce the risk of burns, fire, electric
shock or injury to persons:
1. Close supervision is necessary when this
Groomer is used by, on, or near children or
invalids.
2. Use this Groomer for its intended household
use as described in this manual. Do not use
attachments not recommended by Philips
Electronics North America Corporation.
3. Never operate this Groomer if it has a
damaged cord or charging plug, if it is not
working properly, if it has been dropped or
damaged, or dropped into water. For
assistance call 1-800-243-3050.
4. Keep the Groomer, cord, charging plug and
any attachments away from heated surfaces.
5. Never drop or insert any object into any
opening.
6. Do not operate, charge, clean or plug in
Groomer outdoors or where aerosol
(spray) products are being used or where
oxygen is being administered.
7. Always check foil, cutters, cutting unit, combs
and trimmers before using the Groomer. Do
not use the Groomer if foil, cutters, cutting
unit, combs and trimmers are damaged, as
injury may occur.
8. Always attach plug to Groomer first,
then outlet. To disconnect, turn Groomer
"OFF", then remove plug from outlet.
9. To prevent possible damage to the cord, do
not wrap cord around the Groomer.
10. Never put the Groomer in direct sunlight or
store at a temperature above 140°F.
11. The Groomer. is for use on human hair only.
Do not use the Groomer for any other pur-
pose.
12. Only use the power plug and other
accessories supplied with the Groomer.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains
a transformer. Do not cut off the power
plug to replace it with another plug as this
will cause a hazardous condition.
IMPORTANT: YOUR GROOMER
CONTAINS NICKEL METAL HYDRIDE
RECHARGEABLE BATTERIES.
See Battery Removal Instructions.
Registration
Congratulations on your purchase and welcome
to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.norelco.com/register
4 Clean the combs, attachments and appliance
with the supplied cleaning brush or a dry,
soft cloth.
5 Place the attachment back on the Groomer
handle.
Cleaning the Mini Shaver
1 Separate the top part of the mini shaver
from the bottom part (fig. 22).
2 Blow and/or shake out any hair that may
have accumulated inside the mini shaver
(fig. 23).
3 Clean the top part of the mini shaver under
warm tap water (fig. 24).
w The shaving foil is very delicate and should not
be handled.
w If foil becomes damaged, do not continue using
the mini shaver. Do not apply pressure to shav-
ing foil.
w Do not clean the foil with the supplied brush,
as this may cause damage.
4 Shake excess water from mini shaver and
allow to air dry thoroughly.
Do not use a towel to air dry the mini shaver as
damage to the shaving foil could occur.
This Groomer has no other user-serviceable
parts. For assistance call 1-800-243-3050.
Storage
w Be sure Groomer is turned OFF. Remove cord
from outlet and Groomer before storing in a
safe, dry location where it will not be crushed,
banged, or subject to damage.
w Store the Groomer and attachments in the
pouch to prevent damage.
w Do not wrap cord around Groomer when
storing.
w Store cord in a safe location where it will not
be cut or damaged.
w Do not place or store Groomer where it can
fall or be pulled into a tub or sink, water or
other liquid.
Assistance
For assistance visit our website:
www.philips.com/support
or call toll free: 1-800-243-3050
Online information is available 24 hours a day,
7 days a week.
Battery Removal
w This Philips Norelco Groomer contains
rechargeable Nickel Metal Hydride batteries,
which must be disposed of properly (fig. 25).
w Batteries may only be removed when
Groomer is to be discarded.
w For assistance, visit our website:
www.philips.com/support or
call toll free: 1-800-243-3050.
1 Unplug electrical cord from outlet and
Groomer before dismantling Groomer.
2 Allow the Groomer to run until the
batteries are completely empty/depleted.
Turn Groomer off.
3 Remove any comb and/or attachment from
Groomer.
4 Check if there are any screws in the back or
front of the appliance. If so, remove them.
5 Remove the back and/or front panel of the
appliance with a screwdriver. If necessary,
also remove additional screws and/or parts
until you see the printed circuit board with
the rechargeable batteries.
6 If necessary, cut the wires to separate the
printed circuit board and the rechargeable
batteries from the appliance.
7 Do not attempt to replace batteries. Insulate
battery ends by covering with tape and
or place battery in a small plastic bag.
Discard Groomer.
8 Contact your local town or city officials for
battery disposal information or call
1-800-8-BATTERY or www.rbrc.com for
drop-off locations.
A Mini Foil Shaver
B Nose/Ear Hair Trimmer
C PrecisionTrimmer
D Full Size Metal Guard Trimmer
E Handle
F On/Off Button
G Turbo Button
H Turbo Status Indicator
I Battery Status Indicator
J Storage Pouch
K Small Appliance Plug
L Adapter
M Cleaning Brush
N Stubble Comb
O Beard & Moustache Comb
P Hair Clipping Comb
Full 2-Year Warranty
45-Day Money-Back Guarantee
Put It To The Test
Like many new products, your Philips Norelco
Multigroom Grooming Kit may take a little getting
used to. If you are using an electric Groomer for
the first time, or if you’ve been using a different
brand, take the time to acquaint yourself with your
new Grooming Kit.
Your Multigroom Grooming Kit features head and
facial styling with a powerful battery combined
with all the attachments to make trimming facial
hairs or hair clipping goof proof.
Throw your scissors away and put your new
Multigroom Grooming Kit to the test. We
guarantee precise, professional results or Philips
Norelco will refund you the full purchase price as
long as the request is received within 45 days of
purchase.
P
O
N
M
L
K
A
B
C
D
E
F
G
H
J
3 / 64 - 15 / 32 in
1-12mm
3 / 64 - 23 / 32 in
1-18mm
1 / 8 - 25 / 32 in
3-20mm
I
4222 002 8321 1
Features ENGLISH
Multigroom
Plus
1 2
1
2
3
3 - 20
4
2
3 - 20 1
5 6
7 8
3 - 20 1
3
2
9
10 11 12
1
2
13 14
1
2
15
16
1
2
18 17
19 20 21
22 23 24
25
To Charge/Recharge
w Fully charge Groomer before using for the first
time or after non-use for a long period of time.
w Charging, recharging or using Groomer at
temperatures below 40˚F or higher than 95˚F
adversely affects lifespan of the battery.
w If the Groomer is subjected to a major change
in temperature, pressure or humidity, let the
Groomer acclimatize for 30 minutes before
using.
1 Be certain Groomer is OFF.
2 Connect appliance plug to Groomer and plug
the adapter into any 120V AC outlet (fig. 1).
Use only the cord provided.
w An adaptor plug may be necessary for power
cord usage in some foreign countries. Use an
attachment plug adaptor of the proper
configuration for the power outlet.
3 It will take approximately 1 hour to fully
charge the Groomer for a cordless trimming
time of up to 50 minutes.
4 The Battery Status Indicator will blink green
to indicate Groomer is charging.
5 Disconnect the cord and unplug from
electrical outlet.
Turbo Power
w Simply press the Turbo Button for a turbo
power boost for fast results and the Turbo
indicator will light up green. The memory
function will remember the last used setting.
Corded Trimming
w Groomer does not recharge during corded
trimming.
1 Connect cord provided to Groomer and plug
Groomer into electrical outlet.
2 If battery is completely empty, wait a few
minutes before turning Groomer ON.
3 Press ON/OFF button ON to begin
trimming.
4 Turn Groomer OFF and unplug.
QG3360
Rechargeable Cordless/Cord
Electric Groomer
Always here to help you
Question? Contact Philips Norelco
Question? Contact Philips Norelco
45-DAY MONEY-
BACK GUARANTEE
If you are not fully satisfied with your Philips Norelco
Groomer send the product back and we’ll refund you
the full purchase price.
The Groomer must be shipped prepaid by
insured mail, insurance prepaid, have the original
sales receipt, indicating purchase price and date
of purchase, and the money-back guarantee
return authorization form enclosed. We cannot
be responsible for lost mail.
The Groomer must be postmarked no later
than 45 days after the date of purchase. Philips
Norelco reserves the right to verify the purchase
price of the product and limit refunds not to
exceed suggested retail price.
To obtain money-back guarantee return
authorization form, call 1-800-243-3050 for
assistance.
Delivery of refund check will occur 6–8 weeks AFTER
receipt of returned product.
Full Two-Year Warranty
Philips Electronics North America Corporation warrants each new Philips
Norelco product, Model QG3360 (except cutters, combs and foil) against
defects in materials or workmanship for a period of two years from the
date of purchase, and agrees to repair or replace any defective product
without charge. IMPORTANT: This warranty does not cover damage resulting from
accident, misuse or abuse, lack of reasonable care, the affixing of any
attachment not provided with the product or loss of parts or subjecting
the product to any but the specific voltage.* Use of unauthorized
replacement parts will void this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED REPAIR SERVICE AND WILL NOT
REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM
WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED
REPAIR SERVICE.
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES. In order to obtain warranty service, simply go to www.philips.com/
norelco or call 1-800-243-3050 for assistance. It is suggested that for
your protection you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipment is not covered by this warranty. NOTE: No other warranty, written or oral, is authorized
by Philips Electronics North America Corporation. This warranty gives
you specific legal rights, and you may also have other rights which vary
from state to state. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above exclusion and
limitations may not apply to you. *Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A Division of Philips Electronics North America Corporation P.O. Box 10313, Stamford, CT 06904
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.
Norelco is a Registered Trademark of Philips Electronics
North America Corporation.
PHILIPS is a Registered Trademark of Koninklijke Philips Electronics N.V.
© 2012 Philips Electronics North America Corporation. All Rights Reserved.
The tap symbol on the
groomer indicates that the
groomer can be rinsed under
running tap water.
12_QG3360.indd 1 11/7/12 10:11 AM