Defi Link VSD X - Manual

-1-
Defi-Link VSD X
Operation Manual
C U T H E R E
Product Specifications(for customer and installation personnel)
Power Supply Voltage
Current Consumption
Operational Temperature Range
Storage Temperature Range
Display Range
Applicable Speed Pulse
Applicable Number of Cylinders
Dimensions
Gross Weight
DC10V to 15V（For 12V vehicles）
+B line
IGN line
ILM line
−
20 to ＋60℃, −4 to ＋140゜F （under 80％ relative humidity）
− 40 to ＋80℃, −40 to ＋176゜F （under 80％ relative humidity）
Speedometer（SP）
Engine speed（TA)
Oil temperature（O.TEMP.）
Water temperature（W. TEMP.）
Oil pressure（OIL P.）
Fuel pressure（FUEL P.）
Exhaust temperature（EXT. T.）
A) 2・4・8・16(mainly for Japanese vehicles)
B) Free pulse setting(1,274 pulse/km∼16,562 pulse/km
2,051 pulse/mile∼26,665 pulse/mile)
Without linking: 1・2・3・4・5・6・8 (Set up with D.C.Unit.)
If connected to the Defi-Link Control Unit II Version 2.0(DF05002): 1・2・3・4・5・6・8［※］
If connected to the Defi-Link Control Unit II(DF05001): 3・4・5・6・8［※］
If connected to the Defi-Link Control Unit(DF01301): 3・4・5・6・8［※］
［※
Set up with each control unit.］
Refer to page 2.
820g, 1.8lb（including display unit, D.C.Unit, wires, package）
0∼400km/h（0∼240MPH）
0∼9,500rpm
51∼150℃（123∼302゜F）
21∼120℃（69∼248゜F）
0∼1,000kPa（0∼145PSI）
0∼600kPa（0∼87PSI）
210∼1,100℃（400∼2,010゜F）
DF05704
Defi-Link VSD X is a product to display vehicle information such as speed and engine speed on the Target Screen(the
exclusive reflecting plate). When installing and operating this product, be sure to read the cautionary items of this
operation manual as well as those given in the operation manual for the vehicle in which this display will be installed.
Obtain a full understanding of the cautionary items and use the product accordingly.
In the event that this product (or the vehicle in which it is installed) is lent to or transferred to another person, please be
sure this operation manual accompanies the product.
http://www.defi-shop.com/
In this manual, the degree of hazard arising from actions such as improper operation is separated into the 3 levels “Danger,”
“Warning,” and “Caution.” In addition, instructions that must be followed for safe and proper use of this product as well as
practices that must be maintained are marked with a “Confirmation” heading. Please read and become familiar with these
sections.
Before Installation(for installation personnel)
Warning
disassemble/
modify
Caution
24V
Confirmation
Confirmation
Main Features
（ for customer）
About Installation and Operation(for customer and installation personnel)
Warning
● On no event will Nippon Seiki Co., Ltd. be liable to you for any damages arising out of the use or inability to use the
product, even if Nippon Seiki Co., Ltd. has been advised of the possibility of such damage.
● Do not pull the wires out of connectors forcefully. The connectors may be broken and the wires may be cut. When
pulling out the wires, press the lock firmly and unclip the locks of connectors.
● Do not take off the rubber covering round the target screen. The plate is sharp-edged.
Caution
● The vehicle information other than speed and engine speed is not displayed unless this product is connected to
Defi-Link System.
● The speedometer and the tachometer of this product are for reference purposes only. Please drive according to the
indication of vehicle's originally equipped instruments.
● When this product is linked to the Defi-Link System, connect the LINK connector of the D.C.Unit and the METER
OUTPUT1 connector of the Defi-Link Control Unit II Version 2.0 or the Defi-Link Control Unit II (or the METER
connector of the Defi-Link Control Unit) with the meter wire. Misconnection could damage the product.
● When this product is linked to the Defi-Link system, the tachometer signal must be input to the Defi-Link Control
Unit II(or the Defi-Link Control Unit). Set the number of cylinders of the Defi-Link Control Unit II(or the Defi-Link
Control Unit). Do not connect the Tacho Signal Wire(blue wire) from the D.C.Unit.
● This product can be used only on 1, 2, 3, 4, 5, 6, and 8 cylinder vehicles with 4 cycle engine. However, it cannot be
used on 1 and 2 cylinder vehicles under some circumstances. Refer to the Product Specifications. Engine
revolution signal of diesel vehicles cannot be displayed.
● Data on boost and intake manifold pressure cannot be displayed.
● When this product is linked to the Defi-Link System, be sure to follow the instructions for the Defi-Link Control Unit
II(or the Defi-Link Control Unit).
● The switch illumination of the D.C.Unit is interlocked with turning on/off the ignition of the vehicle.
● The display is high Visibility by adopting the exclusive target screen(the new VSD technology) and super high bright
blue-green VFD
● The brightness is adjusted automatically. (The sensor is included in the product.)
● Two super high bright LED indicators
● The structure of the new mounting bracket allows angle adjustment freely.
● Displays speedometer and engine speed. By connecting to the Defi-Link System, various information is displayed.
● The tachometer can operate with hybrid vehicles and rev limited vehicles by cutting the ignition. (Only if the product
is used without linking to the Defi-Link System or used with linking to the Defi-Link Control Unit II Version 2.0.)
● The switch illumination of the D.C.Unit is interlocked with turning on/off the ignition of the vehicle.
'07.01-1
Warning
Caution
Confirmation
Indicates the possibility of death or serious injury if the product is mishandled.
Danger Indicates the imminent dangerous situation of death or serious injury if the product is mishandled.
Indicates a conceivable source of personal injury or damage to equipment if the product is
improperly operated.
Indicates an instruction that must be performed or practice that must be maintained.
DF05704
Warranty
* Refer to Terms and Conditions
Customer:
Name
Address
Product Name
Lot. No.
Defi Business Division
Ueno DK Bldg 8F, 15-4 Ueno 1-Chome, Taitou-ku, Tokyo 110-0005 JAPAN
E-mail: [email protected]
URL: http://www.defi-shop.com/
1 year
Warranty Period
Date of purchase
• •
’
∼
● Carefully consider the installation location and driver's operation of the product before
installation. Do not install the product where it interrupts driving and the safety deices of vehicle.
Be sure not to install the unit where it could fall. Improper installation or operation could cause
the product to fall and damage the vehicle or cause serious danger by impeding driving.
● Do not disassemble or modify this product. Such actions can not only damage or destroy the
product but will also void the warranty.
● Do not perform installation of this product immediately after the engine has been switched off.
The engine and exhaust system are extremely hot at this time and can cause burns if touched.
● Ensure that the wiring of this product does not have an adverse impact on the other wiring of the vehicle. Any
controlling devices or other electronic components of the vehicle could be damaged.
● Please keep children and infants away from the installation area. Children may swallow small parts or be injured in
other ways.
Danger
● Ensure that the vehicle will remain stationary and turn off the engine before installing this product. Failure to do so could
result in a fire, and could make the vehicle move during installation.
● Remove the key from the ignition and disconnect the negative (-) battery terminal prior to installation of this product.
Failure to do so could result in a fire caused by an electrical short circuit.
● Take care not to install this product in a way that interferes with safety equipment such as seat belts and air
bag systems or vehicle operation equipment such as engine controls, steering wheel or brake systems.
Interference with normal operation of the vehicle can result in an accident or fire.
● Solder or use a solderless connector for wiring connections and make sure connections are insulated. In
areas where there could be tension or sudden impacts on the wiring, safeguard the wiring with corrugated
tubing or other shock absorbent material. Accidental shorts can cause fires.
● This product is designed for use on 12V vehicles. Do not install this product on vehicles with 24V
systems.
● Insulate any unused wires. If any wires or connectors loosen during installation, please make
sure they are correctly reattached.
● Dropping any of the components of this product will result in damage to the product.
● Excessive force on switches/terminals may result in damage to the product.
● Use only the wires provided. If additional wires are required, use the same of quality and gauge wire as is provided
with the kit.
● Do not attach wires on the body of the vehicle or engine parts as this may result in damage to the product.
● Install sensors away from heat and moisture to avoid damage.
● Install sensors away from ignition and also radio signal frequency interference as this could cause the gauges to
malfunction.
● Do not wire the sensor wires near the engine, exhaust pipe or turbine. It may result in damage or fusion of wires.
● Do not expose D.C.Unit to moisture, dust or direct sunlight. Do not place product directly in front of heat vents.
● Wear gloves to avoid burns when soldering and cuts when working with wiring.
● Make sure the waterproof processing is done when diverging wires in the
engine compartment.
● Do not pull the wires out of connectors forcefully. The connectors may be
broken and the wires may be cut. When pulling out the wires, press the
lock firmly and unclip the locks of connectors.
● Be sure to follow all instructions in this manual to ensure safe installation and operation of the product.
● When the negative (-) battery terminal is disconnected, equipment such as clocks and audio components having
internal memory may lose their memory data. Follow the operation manual of each component to reset data after
installation of this product.
● After installation is complete, return this operation manual and the package to the customer along with the warranty.
● Please have this product installed by the retail store or dealer where it was purchased. Installation by the customer
will void the warranty.
● Do not disassemble or modify this product. Such actions can not only damage or destroy the product but will also
void the warranty. This product is high-voltage, and there is an possible to get an electric shock.
● In order to ensure safe driving, check the information on this display only for short periods of time. Looking at the
display for long periods of time could distract adequate attention from the road and result in an accident.
● Discontinue use of this product if nothing is displayed, water gets into the unit, or smoke or a strange odor comes
from the unit. If such a condition occurs, contact the sales outlet or installation personnel as soon as possible.
Continued use while the condition exists could result in an accident or fire.
● Do not operate during driving.
MAX 1A only while the closing mode is displayed. (Dark current 0mA)
MAX 1A
MAX 0.1A