Defi Link VSD X - Manual (Page 2)

-2-
Target
Screen
DIM Sensor
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
⑫
⑬
⑭
D.C.Unit
58
°
1
7/
16
(3
6.
7) 3
5/
8
(9
2.
3)
3 13/16 (97.3)
2
13
/1
6
(7
1.
9)
Display
Position
Indicator(green LED) Indicator(red LED)
Rubber for Target Screen
4 7/16 (112)
2
1/
2
(6
3.
2)
15
/1
6
(2
4.
5)
Control Out Wire(pink) 3 1/3ft, 1m [※1]
[※1 Use only when connected to the Defi-Link system]
Part Names and Dimensions in inches(mm)
The following parts are included with this product. Confirm that all parts are present before installing the product. In
addition, these parts are sold separately for part replacement. Contact your retailer for further information.
NOTE: A Japanese operation manual, a wiring manual, and a questionnaire card are included other than the parts
listed below. They are effective only in Japan.
Parts List
（ for customer and installation personnel）
Optional Parts(for customer)
Part Name Quantity
Display unit(wire 8 1/3ft, 2.5m) 1
1
1
1
1
1
1
D.C.Unit(Exclusive Control Unit)
Speed & Tacho Signal Wire
(Green SP, Blue TA) 6 2/3ft, 2m
Tachometer Signal Wire（Blue） 6 2/3ft, 2m
[※1]
DIM Sensor(wire 6in, 0.15m)
Power Supply Wire 2 3/2ft, 0.8m
Meter Wire 10in, 0.25m [※1]
Power Supply Link Wire 10in, 0.25m [※1]
Part Name Quantity
1
1
2
1each
6
Operation manual
Terms and Conditions
Mounting Bracket Set [※2]
Double-sided tape
M4 Bolt, Nut, Washer
1
2 Tapping screw(for Mounting Bracket)
1 Mounting Bracket
1
Item
Defi-Link Oil Pressure Sensor Set(Sensor thread size: 1/8PT)
Defi-Link Fuel Pressure Sensor Set(Sensor thread size: 1/8PT)
Defi-Link Oil Temperature Sensor Set(Sensor thread size: 1/8PT)
Defi-Link Water Temperature Sensor Set Sensor thread size: 1/8PT)
Defi-Link Exhaust Temperature Sensor Set(Sensor thread size: 1/8PT)
Defi-Link Control Unit II Version 2.0
Part Number
PDF00713SS
PDF00806SS
PDF00908SS
PDF01006SS
PDF01114SS
Oil/Water Temp. Sensor(Sensor thread size: 1/8NPT) PDF03905S
1/8 NPT/PT Conversion Socket for pressure sensor
1/8 NPT fitting for Exhaust Temp. Sensor PDF00708G
PDF01109G
DF05002
Replacement Parts(for customer)
Item
Mounting Bracket set [※2 Refer to the Parts List for the contents]
Part Number
Rubber for Target Screen
Fuse for Power Supply Wire(4A) 2pcs PDF05005G
PDF05711G
PDF05712G
4 Clamp
Solderless connector
SELECT/▽DOWN SWITCH
BAR SELECT/▲UP SWITCH
ENTER/DIM/SET UP SWITCH
PEAK/RESET SWITCH
For Display unit
For Speed & Tacho signal wire(White)
For Power supply wire / Power supply link wire(White)
For Power supply wire / Power supply link wire(White)
For Control Unit II / Control Unit / Gauge / Display(White)
For Control Unit II / Control Unit / Gauge / Display(White)
For Control Unit II / Control Unit / Gauge / Display(White)
For Control output(Red)
Unused(Black)
Storage space for wires ⑩ through ⑬
Wires connected to ⑩ through ⑬ can be fit in the place neatly.
Trouble Shooting(for customer and installation personnel)
● If operation of the product seems unusual, inspect the product to confirm that there is no malfunction. If an
operational problem has occurred, it could result in an accident.
Phenomenon Possible Cause Corrective Action
Warning
○ Wiring of the power supply wire or the
display wire is improper.
○ The fuse is blown out.
○ The locks of the solderless connectors
are not locked tightly.
○ Does not display.
○ The gauge doesn't perform
the opening and the closing
mode. Power is not
supplied.
○ Check wiring as per instructions in this manual.
○ Make sure the wiring is not touched on the
vehicle body and then change the fuse.
○ Check the lock of the solderless connectors.
○ Wiring of the tachometer signal wire is
wrong.
○ Setting of the number of cylinders is
wrong(D.C.Unit/Defi-Link Control Unit
II/Defi-Link Control Unit).
○ LINK of D.C.Unit and METER OUTPUT2
of Defi-Link Control Unit II are connected.
○ The tachometer signal wire is not
connected to Defi-Link Control Unit II or
Defi-Link Control Unit (in the case that
the product is connected to the Defi-Link
System).
○ The engine speed is not
displayed correctly.
○ Check wiring as per instructions in this manual.
○ Check the number of cylinders as per instructions
in this manual and the manuals of the Defi-Link
Control Unit II or the Defi-Link Control Unit.
○ Connect the LINK connector of the D.C.Unit and
the METER OUTPUT1 connector of the Defi-Link
Control Unit II using the meter wire.
○ Connect the tachometer signal wire to the Defi-
Link Control Unit II(or the Defi-Link Control Unit).
○ Wiring of the speed signal wire is
wrong.
○ Setting of the speed pulse is wrong.
○ The speed is not displayed
correctly.
○ Check wiring as per instructions in this manual.
○ Check the speed pulse as per instructions in this
manual.
○ The DIM sensor is not connected.
○ The front of the DIM sensor is
obstructed.
○ The manual dimmer mode is selected in
the setting of the illumination control.
○ The direction of the DIM sensor is
wrong.
○ The auto dimmer mode is
on, but the display is dark
or the brightness of the
display doesn't change.
○ Connect the DIM sensor as per instructions in this
manual.
○ Attach the DIM sensor in a position without any
obstruction which interrupts the front of the sensor.
○ Reset the illumination control setting as per
instructions in this manual.
○ The wiring of the red line of the power
supply wire is wrong.
○ Does not carry out the
closing mode.
○ Check wiring as per instructions in this manual.
○ The REC button is pressed when the
vehicle is stationary.
○ The product is connected to
the Defi-Link System, but
the speed is not recorded.
○ Press the REC button when the vehicle is moving.
○ The condition is normal. ○ Switching of the unit
illumination is not
interlocked with switching of
the vehicle illumination.
○ Switching of D.C.Unit illumination is interlocked
with turning on/off the ignition.
※ In addition to a general inspection of the product, use the following table to confirm proper operation of the unit. If the
operational problem does not appear in the following table, contact the installation personnel.
3 3/4 (95.6)
13
/1
6
(9
6.
8)
1
1/
16
(2
7.
5)
① ② ③ ④
⑤ ⑥ ⑦ ⑧ ⑨
⑩
⑪
⑫
⑬
⑭
○ The setting of the speed pulse or the
number of cylinders is wrong.
○ The information on the
display is not the same as
that on the originally
equipped gauges.
○ Recheck the setting and setup again. When the
setting is not wrong, it depends on the margin of
error. Drive according to the indication of
originally equipped gauges.
○ The angle of the display unit is not
proper.
○ The display is dark. ○ Adjust the angle of the display referring to How to
install / Step3 / ②The angle of the display.
Display Unit
Connector for the DIM Sensor(Black)
Driving direction
7/16 (11.2)
9/
16
(1
4.
4)
Sensing part
1 5/16 (33)
Pop Demo of Special Display Pop Demo of Special Display
When the Pop demo is selected for the special display, the following demo is played.
Refer to Operation / ⑤Setting of Special Display.