JLG 110HX ANSI Operator Manual - Manual (Page 66)

SECTION 5 - OPTIONAL EQUIPMENT
5-2 – JLG Lift – 3120635
5.8 ROTATING BEACON
An amber or red rotating beacon may be installed on the
hood or platform, and can be controlled by a two position
toggle switch mounted on the platform control console.
When the switch is placed in the ON position, the light is
activated and provides a visual warning to the machine’s
operation.
5.9 CYLINDER BELLOWS
A one piece accordion shaped rubber bellows may be
attached to the rod end of the cylinder barrel and to the
cylinder rod as close to the rod attach bushing as possi-
ble. The bellows affords protection to the cylinder rod in
either the extended or retracted position. The bellows are
installed on the lift cylinder, slave cylinder, master cylinder
and steer cylinder.
5.10 BOOM WIPERS
A one piece U-shaped neoprene strip, be attached to the
front of the base boom section, wipes the top and both
sides of the fly section. The bottom side of the fly section
is protected by a straight neoprene strip which also
attaches to the base section.
5.11 HOSTILE ENVIRONMENT PACKAGE
The hostile environment package provides additional pro-
tection against the entry of dust, dirt, sand and other abra-
sive materials into the hydraulic system, control handles
and switches, cylinders, boom wire ropes and wear pads,
and the air inlet of the engine. The package is intended for
machines that will be exposed to painting, sandblasting or
other similar hostile conditions. The hostile environment
package includes boom wipers, cylinder bellows, heavy
duty reservoir breather, an engine air cleaner and control
console cover, as required.
5.12 MOTION ALARM
A motion alarm horn provides an audible warning when
the platform controls are selected at the PLATFORM/
GROUND SELECT switch, the POWER/EMERGENCY
STOP switch is ON, and the footswitch is depressed. The
alarm warns personnel in the jobsite area to avoid the
operating machine.
5.13 DESERT ENVIRONMENT PACKAGE
The Desert Environment package is designed to provide
additional protection to the machines vital components
under extreme hot, dry and sandy conditions. This pack-
age includes the boom wipers, cylinder bellows, heavy
duty air cleaner, console cover, and air breather described
in the Hostile Environment package in this section. In
addition to these items a hydraulic oil cooler fitted with a
sand and dust filter is installed on the machine turntable.
A hydraulically driven motor serves to turn the fan which
draws air down through the sand and dust filter. The air is
then forced down through the heat exchanger cooling the
constant flow of hydraulic oil within.
5.14 110 VOLT/60HZ GENERATOR
A 110 volt generator, mounted beside the engine, is belt
driven from the output shaft of the engine. This application
provides for a 110 volt receptacle at the ground control
and also at the platform. The lead from the ground control
and also at the platform. The lead from the ground control
to the platform is routed along the boom power track thus
eliminating the use of extension cords hanging freely from
the platform.
5.15 220 VOLT RECEPTACLE
A 220 volt receptacle may be mounted on the platform
support to eliminate extension cords hanging from the
platform. The lead from the receptacle is routed along the
boom power track to the engine compartment. In the
engine compartment, a plug is installed on the lead for
attachment to an extension cord or a receptacle from a
220 volt power source. When not in use the plug is stored
in a junction box mounted on the engine compartment
frame.
5.16 SPARK ARRESTOR MUFFLER
The spark arrestor is mounted directly aft of the standard
muffler and serves to contain any sparks the engine might
emit that a standard muffler normally would not. The spark
arrestor is a vital option for machines which are operated
in areas where combustible materials are used. The spark
arrestor is available for gasoline, LP gas, and diesel
engines.
5.17 110 VOLT RECEPTACLE
A 110 volt receptacle may be mounted on the platform
control console to eliminate extension cords hanging from
the platform. The lead from the receptacle is routed along
the boom power track to the battery and ground control
compartment at the front of the machine. A plug is
installed on the end of the lead for attachment to an exten-
sion cord or a receptacle from a 110 volt power source.
When not in use the excess wire and plug are to be
stowed beside the battery.