APG PT-L10-C datasheet - Manual (Page 3)

Options
PT- ____ - C - _____ - _____ - _____ - _____ - _____ - _____ - _____ - _____ - _____ - _____ - _____
A B C D E F G H I J K L
A. Operation
□ L1 4-20 mA □ L11 1-6 VDC
□ L3 0-5 VDC □ L12 1-5 VDC
□ L10 0-10 VDC
B. Common Pressure Ranges
□ 5 □ 50 □ 200 □ 1000 □ 5000
□ 15 □ 60 □ 300 □ 2000 □ 10000
□ 30 □ 100 □ 500 □ 3000
*Other ranges available
C. Unit of Measure
□ PSI▲ □ kPa □ inHg
□ bar □ inH
2
O □ kgcm 2
□ mbar □ mmHg □ fsw
D. Pressure Type
□ G Gauge □ A Absolute
□
CG Compound Gauge
□
S Sealed
□ V Vac
E. Electrical Connection
Mating connector sold separately
□ E1 6-pin circular □ E5▲ Pigtail with cable
□ E3 4-pin bayonet □ E17 6-pin bayonet
□ E4 4-pin M12 Micro connector
F. Elelectircal Cable Length
Use with E1, E3, E4, E17 connections
□
W0 0 ft
Use with E5 pigtail connection
□
W1 2 ft (0.6 m)
□
W4 25 ft (7.6 m)
□ W2 5 ft (1.5 m) □ W5 50 ft (15.2 m)
□ W3 10 ft (3 m)
Automation Products Group, Inc. www.apgsensors.com
tel. 888.525.7300 [email protected]
3
G. Process Connection
□ P0▲ 1/4-18 NPTM □ P16 PT 1/4 (BSPP) male
□ P2 1 1/2 sanitary □ P22 G3/8 (3/8 BSPP) male
□
P4 7/16-SAE male flush mount
□ P5 1/4-18 NPTF □ P23 G1/2 (1/2 BSPP) male
□
P7 7/16-20 SAE male
□
P26 7/16-20 UNF male w/
cone
□ P14 1/8-27 NPTM □ P30 High Pressure Sno Trik
(M-250C, Autoclave male)
H. Accuracy
□ N0▲ ±0.25%
□ N1 ±0.25% with NIST certification
□ N2 ±0.1% with NIST certification
□ N3 ±1% or better
□ N4 ±1% or better with NIST certification
□ N12 ±0.5% (standard on ranges greater than 5000
psi and voltage output only)
□
N13 ±0.5% with NIST certification
I. Materials
□ M0 15-5 SS
□ M1▲ 316L SS or 316L/Hastelloy
□
M5 Hastelloy (minimum quantities required)
J. Vibration
□ V0▲ Standard
□ V1 High (not available with K0)
K. Can Assembly
□ K0▲ Knurl
□ K1 Tamper resistant with Loc-Tite
□ K2 Tamper resistant with weld
□ K3 Weld can to fitting and connector
L. Temperature
□
S0▲ Standard: 0º - 130ºF (-17º - 54ºC)
□ S1 Extended: -40º - 180ºF (-40º - 82ºC)
Note:
▲
Indicates this option is standard.