Document Outline

• INTRODUCTION
  • 1.1 Sensor Head Description and Function
  • 1.2 Transmitter Description and Function
• 2 INTELLECTUAL PROPERTY NOTICES
• 1
• 3 EQUIPMENT SAFETY COMPLIANCE
  • 3.1 Safety
  • 3.2 North American Emissions
  • 3.3 European Emissions and Immunity
  • 3.4 CE Marking
• 4 WARRANTY
• 5 GENERAL SAFETY GUIDELINES
  • 5.1 Introduction
  • 5.2 Safety Precautions
  • 5.3 Definitions of Symbols
    • 5.3.1 General Warning or Caution
    • 5.3.2 Grounding
    • 5.3.3 On
    • Off
    • 5.3.5 General Warnings
    • 5.3.6 General Cautions
• 6 UNPACKING AND PARTS LIST
  • 6.1 Unpacking
  • 6.2 Inventory of Parts
  • 6.3 Class I, Division 2 Labels
• 7 SENSOR INSTALLATION
  • 7.1 Class I, Division 2, Groups A, B, C, and D Rated Equipment
  • 7.2 Tools Required For Installation
  • 7.3 Sensor Installation Guidelines
    • Feature
  • 7.4 Process Piping Considerations
    • 7.4.1 Pipe Preparation
    • 7.4.2 Determine the Pipe Inner Diameter (ID)
  • 7.5 Sensor Band Installation
    • 7.5.1 Sensor Band Short Test
    • 7.5.2 Sensor Band Thermal Barrier Installation
  • 7.6 Sensor Cover Installation
    • 7.6.1 Fiberglass Cover Installation
    • 7.6.2 Stainless Steel Cover Installation
      • 7.6.2.1 Boot Gasket Band Installation
      • 7.6.2.2 Boot Gasket Fender Assembly Installation
    • 7.6.3 Sensor Assembly Cable Connection
    • 7.6.4 Rain Boot Installation
    • 7.6.5 Sensor Calibration Label
  • 7.7 Sensor to Transmitter Cable Connections
    • 7.7.1 Sensor End Cable Attachment
  • 7.8 Installations on Tubing
• 8 TRANSMITTER INSTALLATION
  • 8.1 Transmitter Power Requirements
  • 8.2 Transmitter Environmental Conditions
  • 8.3 Transmitter Mounting Instructions
    • 8.3.1 Bulkhead Mounting
    • 8.3.2 Pipe Mounting
  • 8.4 Transmitter Cable Connections
    • 8.4.1 Transmitter Housing Cable Entry
    • 8.4.2 Transmitter Output, Sensor and Sensor Head Connections
      • 8.4.2.1 Transmitter Output Connections (Section #1)
        • Comment
      • 8.4.2.2 Transmitter Input Connections (Section #2)
      • 8.4.2.3 Sensor Head to Transmitter Cable Connections (Section #3)
        • 8.4.2.3.1 Non-armored cable installation
        • 8.4.2.3.2 Armored cable installation
    • 8.4.3 Transmitter Electrical Power Cable Installation
      • 8.4.3.1 AC-Powered SONARtracTM
      • 8.4.3.2 DC-Powered SONARtracTM
    • 8.4.4 Sensor Calibration Label
• 1
• 9 TRANSMITTER FUNCTIONS
  • 9.1 Transmitter Layout
  • 9.2 Transmitter Output Definitions
  • 9.3 Transmitter Input Definitions
  • 9.4 Keypad
  • 9.5 Transmitter Display
    • 9.5.1 Operational Mode
      • 9.5.1.1 System Start
      • 9.5.1.2 Operating Transmitter Display
        • 9.5.1.2.1 Line 1 / Line 2
        • 9.5.1.2.2 Status Line
      • 9.5.1.3 Display Examples
    • 9.5.2 Menu Mode
      • DIAGNOSTICS
      • Sensor
• 10 TRANSMITTER SETUP
  • 10.1 Transmitter Menus
    • 10.1.1 Basic Config Menu
    • 10.1.2 Output Config Menu
      • 10.1.2.1 SONARtracTM Filters
    • 10.1.3 Input Config
    • 10.1.4 Customize Menu
    • 10.1.5 Communications Menu
    • 10.1.6 Diagnostics Menu
    • 10.1.7 Info Menu
  • 10.2 Resetting Processor
  • 10.3 Resetting to Factory Defaults
• 11 TRANSMITTER STARTUP & OPERATION
  • 11.1 Initial Start-up
    • 11.1.1 Initial Setup
• 12 TRANSMITTER USB PORT
  • 12.1 USB Port File Naming Convention
  • 12.2 Save Snapshot
  • 12.3 Load Configuration
  • 12.4 Advanced Functions
• 13 SENSOR REMOVAL PROCEDURE
• 14 PROCESS PIPE ROTATION AND PIPE REPLACEMENT
  • 14.1 Pipe Rotation
  • 14.2 Pipe Replacement
• Appendix A SONARtracTM HD VF-100 SPECIFICATIONS
• Appendix B SONARtracTM EC DECLARATION OF CONFORMITY
• Appendix C SYSTEM CONTROL DRAWING SONARtracTM, NON-INCENDIVE
• Appendix D MATERIAL SAFETY DATA SHEETS
• Appendix E CONVERSION FACTORS
• Appendix F PHYSICAL PROPERTIES OF WATER
• Appendix G END USER LICENSE AGREEMENT
• Appendix H SPARE PARTS LIST
• Appendix I DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)
  • CiDRA Corporation