Daisy PowerLine 35 - Manual (Page 5)

8
Step 7. TAKE “OFF” TRIGGER SAFETY
When you are certain the target, backstop and surrounding area is
safe, take trigger safety “OFF” by pushing from right to left so that red
is exposed. Your gun is now cocked and ready to shoot. In this condi-
tion, it should be handled with extreme care.
Step 8. FIRE
After making sure the gun is pointed in a safe direction, gently (but
firmly) squeeze the trigger. Repeat Steps 1 through 8 to continue
shooting, using the appropriate loading procedure.
NOTE: To fire, bolt
must be completely closed as indicated in Step 5.
CAUTION:
Do not leave your gun pumped for an extended
period of time. This could result in a time delay from the time the trig-
ger is pulled until the projectile is expelled from the gun. Also, leaving
your gun pumped for more than one hour could result in permanent
damage to the air release valve.
WARNING:
If a BB or pellet does not fire after completing the
operation steps, the gun is jammed. This is a dangerous condition.
CLEARING A JAM
Open the bolt and put “ON” trigger safety immediately. If the bolt is
not completely closed, do not try to close it until after opening it by
pulling the bolt handle all the way back. The gun will not fire a projec-
tile when the bolt is completely open.
Repeat all operations except Step 4 (do not load BB or pellet),
pumping gun up 10 times. If a projectile still does not fire, follow
these steps carefully:
1. Open bolt.
2. Put trigger safety “ON”.
3. Clear barrel by running a cleaning rod through from the muzzle
end. Be careful not to damage the bolt tip by pushing the rod through
too hard. Do not reuse this BB or pellet.
4. Repeat operation steps. Make sure a BB or pellet is fed into firing posi-
tion. If after following the firing procedure the projectile is not fired, return
your gun to Daisy (See “REPAIR OF DAISY GUNS” section).
UNLOAD PELLETS:
The magnetic tip does not extract a pellet. You must shoot the pellet out if a
safe target is available. If a safe target is not available, open bolt, put trig-
ger safety “ON”, insert a cleaning rod in the muzzle end and push the
Blade Front Sight / La hoja la Vista Anterior / La Vue de Devant de lame
Too High
También Alto
Aussi Haut
Too Low
También Bajo
Trop Bas
Just Right
Apenas Correcto
A la perfection
Fiber Optic Front Sight
La fibra la Vista Anterior Optica / Fibre la Vue de Devant Optique
Just Right
Apenas Correcto
A la perfection
Too Low
También Bajo
Trop Bas
Too High
También Alto
Aussi Haut
Step 5. CLOSE BOLT
Close bolt by pushing fully forward on bolt handle to chamber either
a BB or pellet and lock the bolt.
CAUTION:
The gun is now loaded and ready to fire.
Step 6. AIM AT SAFE TARGET
Aim the gun at a safe target. To be a consistent marksman, use the
correct sight picture each time you fire your gun (Fig. 8).
Never point
a gun, loaded or unloaded, at anyone.
CAUTION:
Due to the power of this air gun, use extra cau-
tion in selecting a safe target backstop. Select the proper target and
backstop based on the ammunition you are shooting. BBs should
NEVER be shot into a pellet trap. Pick targets with a backstop that
cannot be penetrated or that will not cause ricochet because of their
hard surface. Use only targets and traps that are designed for use
with high power air guns. Do not shoot at water.
9
Fig. 8
HOW TO ADJUST SIGHT LEFT OR RIGHT
CÓMO AJUSTAR LA MIRA HACIA LA IZQUIERDA O HACIA LA DEREC
COMMENT RÉGLER LE DISPOSITIF DE VISÉE VERS LA GAUCHE OU VERS LA DROITE
HOW TO ADJUST SIGHT UP OR DOWN (ELEVATION)
CÓMO AJUSTAR LA MIRA HACIA ARRIBA O HACIA ABAJO (ÁNGULO DE ELEVACIÓN)
COMMENT RÉGLER LE DISPOSITIF DE VISÉE VERS LE HAUT OU VERS LE BAS (ÉLÉVATION)
Fig. 9
Fig. 10
SCREW “A”
TORNILLO "A"
VIS « A »
WINDAGE
CORRECCIÓN POR EL VIENTO
DÉRIVE
SIGHT ELEVATOR
ELEVADOR DE LA MIRA
INTERCALAIRE DE VISÉE
CORRECT SIGHT ELEVATOR POSITION
CORRIJA LA POSICIÓN DE ELEVACIÓN DE LA MIRA
POSITION DE L’INTERCALAIRE DE VISÉE À POINT
LOWER / BAJE / RABAISSER
pellet out of the barrel. Do not allow a pellet to fall into the rear of the
loading port and become jammed in the BB feed hole.
TO EMPTY BB MAGAZINE:
Open bolt and put trigger safety “ON”. Open the BB magazine
door, cup your hand over it and tilt the gun fully to the left side. Shake
gun until all BBs are removed. Then remove BBs from loading port
(Fig. 2).
WARNING:
Even if you have fired the airgun one or more
times and no BB or pellet was expelled, it does not mean that the gun
is empty of ammo. Continue to treat the airgun as it is loaded.
WARNING: Never assume gun is empty of projectiles.
Always point the gun in a safe direction.
REAR SIGHT ADJUSTMENT:
Your air gun is equipped with an adjustable rear sight.
HOW TO ADJUST SIGHT RIGHT OR LEFT (WINDAGE):
Loosen screw “A” by turning counterclockwise (Fig. 9). Move rear sight
to the right side of the gun to make it shoot to the right, or to the left
side of the gun to make the gun shoot to the left. Make certain screw
“A” is retightened after adjustment.
HOW TO ADJUST SIGHT UP OR DOWN (ELEVATION):
Raise the rear sight by moving sight elevator back to make the gun
shoot higher. Lower the rear sight by moving the sight elevator for-
ward to make the gun shoot lower (Fig. 10).
RAISE / EL / SURÉLEVER EVE
PROPER CARE
To maintain top shooting performance, lightly oil the three pumping
lever hinges and the felt wiper on the piston every 1,000 shots
(Fig. 11). Use a 10-, 20- or 30-weight non-detergent, automotive
motor oil.
DO NOT use light, household type oils or aerosol type
spray lubricants since they may contain substances or additives harm-
ful to the rubber seals or other components. Clean the exterior by wip-
ing with a soft, clean, lightly oiled cloth. The screws are a gun blue fin-
ish; wipe with oil to prevent rust.
CAUTION:
Improper lubricants, such as aerosol type spray
lubricants, can ignite (diesel) during pumping. Use only automotive
motor oils.
FELT PAD
ALMOHADILLA
DE FIELTRO
TAMPON DE FEUTRE
PUMPING FOREARM
PALANCA DE BOMBEO
LEVIER DE POMPAGE
HINGES
BISAGRAS
CHARNIÉRES
PUMP ROD
VARILLA DE BOMBEO
TIGE DE POMPAGE
Fig. 11