GAM DISC TRAY TS6130 User Manual

Product instructions

Advertising
background image

Page 1 of 2

www.rosco.com

GAM Product #TS6130

Rosco Product # 206 3630 00000

CAUTION

When using a DMX device with a discharge lamp such

as CDM or an HMI, it’s suggested that you separate the

power circuit for the discharge lamp from the DMX control

device. When using DMX controlled units such as an In-

dexing TwinSpin™ or SX4® Gobo Changer or DMX Loop

Tray, the “noise” from the discharge lamp ballast may

cause some interference and or damage the electronics.

For best results we recommend providing separate line

voltage to the DMX devices and the discharge light fixture.

PRODUCT INSTRUCTIONS

SX4® DISC TRAY

The SX4® Disc Tray fits in the same SX4® housing as

the Loop, Six-Gobo and Four-Gobo Trays. It utilizes

the same DMX Dual Power Supply as the Six and

Four-Gobo Tray. The Disc Tray can be operated using

a DMX signal, or it can be simply turned on and off

using built-in programs

STANDALONE MODE

Select speed and direction of rotation using the 4

Channel and Mode Selection switches mounted on

the Dual Power Supply. In this mode of operation, the

unit will turn on and off when you power it. To operate

in this fashion, follow the following instructions:

MODE = 5

Stand Alone Continuous Rotation

X100 sets clockwise or counter-clockwise rotation.

Odd numbers (1,3,5) set counterclockwise, even

numbers set clockwise.

X10 and X1 sets speed of rotation.

X10 at 0 and X1 at 0 is slowest rotation.

X10 at 6 and X1 at 3 is fastest possible rotation.

CONTROL YOUR DISC TRAY WITH A DMX SIGNAL.

In order to do that, you will use the mode and chan-

nel select switches on the DMX Control Dual Power

Supply, and follow the following procedure:

MODE = 6

DMX Controlled Continuous Rotation

Set channel selection with X100, X10, X1 to desired

DMX channel. Example: X100 at 0, X10 at 0, X1

at 1 means unit will operate on DMX channel one.

Run the fader up and down. 0% to 50% is fast

to slow Clockwise. 51% to 100% is slow to fast

counter clockwise.

The SX4® Disc Tray fits in the same SX4® housing as the Loop,

Six-Gobo and Four-Gobo Trays. It utilizes the same DMX Dual

Power Supply as the Six and Four-Gobo Tray.

Select speed and direction of rotation using the 4 Channel and

Mode Selection switches mounted on the Dual Power Supply.

In this mode of operation, the unit will turn on and off when you

power it. To operate in this fashion, follow the

following instructions:

X100 sets clockwise or counter-clockwise rotation.

Odd numbers (1,3,5) set counter-clockwise, even numbers set clockwise.
X10 and X1 sets speed of rotation.

X10 at 0 and X1 at 0 is slowest rotation.

X10 at 6 and X1 at 3 is fastest possible rotation.

Set channel selection with X100, X10, X1 to desired DMX channel. Example: X100 at 0, X10 at 0, X1 at 1 means

unit will operate on DMX channel one. Run the fader up and down. 0% to 50% is fast to slow Clockwise.

51% to 100% is slow to fast counter clockwise.

TO CONTROL YOUR DISC TRAY WITH A DMX SIGNAL. In order to do that, you will use the mode and

channel select switches on the DMX Control Dual Power Supply, and follow the following procedure:

The Disc Tray can be operated using a DMX signal, or it can be

simply turned on and off using built-in programs.

SX4

®

DISC TRAY OPERATING INSTRUCTIONS

STAND-ALONE MODE

MODE = 5

Stand Alone Continuous Rotation

MODE = 6

DMX Controlled Continuous Rotation

X1

MODE

X10

X100

MODE 7 OPERATION • MODE SWITCH = 7

DMX single channel linear indexing and

rotation control

Select DMX control channel on SX4® switches:

X100, X10, X1. Control channel fader operates

index/rotate functions as per chart below:

DMX Level

255

130

129

128

0

Channel Level

100%

52%

51%

50%

0%

Direction

Slow clockwise
Variable speed levels

Continuous rotation
Fast clockwise

STOPPED

360 degrees
Indexing to position

with shortest route

maximum speed

0 degrees (home)

Advertising