HMC Electronics EDU2AE Kolver Programmable Power Control Unit for PLUTO Electric Torque Screwdrivers User Manual
Page 4
If you decide to work thru EXT Program, you need first to set all the parameters of programs 1...8 and then
select the EXT program; when working thru EXT program, no modification of programs 1..8 are possible.
Other parameters are the same as standard EDU1AE unit.
TORQUE: you can select the desired torque as a percentage of the torque range of the selected screwdriver.
For example, for a Pluto10, a 50% setting on hard joint will result in a torque in the area of 6 Nm.
Model
Code
Control unit
Torque (Nm)
Speed
Output
Dimensions L
x ø mm
SOFT
HARD Min Max
Pistol grip (PLUTO P)
PLUTO 3P
130204
EDU1AE/LTP 0,3-2
0,6-3
390 1200 Hex 1/4" 150x150x45
PLUTO 10 P/N
130210/N
EDU1AE/LTP 0,7-3,6 0,6-4,0 130 400
Hex 1/4" 150x150x45
EDU1AE
2-8
2-9,8
200 600
PLUTO 15 P/N
130215/N
EDU1AE/LTP 0,6-6,3 1,4-6,8 70
220
Hex 1/4" 150x150x45
EDU1AE
2-13,5
2-14,7
100 320
Pistol grip top connector (PLUTO P/U)
PLUTO 3P/U
130204/U
EDU1AE/LTP 0,3-2
0,6-3
390 1200 Hex 1/4" 150x150x45
PLUTO 10 P/U/N
130210/U/N
EDU1AE/LTP 0,7-3,6 0,6-4,0 130 400
Hex 1/4" 150x150x45
EDU1AE
2-8
2-9,8
200 600
PLUTO 15P/U/N
130215/U/N
EDU1AE/LTP 0,6-6,3 1,4-6,8 70
220
Hex 1/4" 150x150x45
EDU1AE
2-13,5
2-14,7
100 320
In-line (PLUTO D)
PLUTO 3D
130203
EDU1AE/LTP 0,3-2
0,6-3
390 1200 Hex 1/4" 216x40
PLUTO 10 D/N
130211/N
EDU1AE/LTP 0,7-3,6 0,6-4,0 130 400
Hex 1/4" 216x40
EDU1AE
2-8
2-9,8
200 600
PLUTO 15 D/N
130216/N
EDU1AE/LTP 0,6-6,3 1,4-6,8 70
220
Hex 1/4" 216x40
EDU1AE
2-13,5
2-14,7
100 320
Automation (PLUTO CA)
PLUTO 3CA
130303
EDU1AE/LTP 0,3-2
0,6-3
390 1200 Hex 1/4" 164x40
PLUTO 10CA/N
130211/N
EDU1AE/LTP 0,7-3,6 0,6-4,0 130 400
Hex 1/4" 164x40
EDU1AE
2-8
2-9,8
200 600
PLUTO 15CA/N
133216/N
EDU1AE/LTP 0,6-6,3 1,4-6,8 70
220
Hex 1/4" 164x40
EDU1AE
2-13,5
2-14,7
100 320
PLUTO 20CA
130303
EDU1AE/20
2,5
20
43
130
Sq 3/8 ''
200x45,5
JOINT: You can select the type of joint (soft or hard) you are working on. A soft joint is typically a self
tapping screw on plastic or sheet metal, or a metric (machine) screw on a material subject to strain (for
example: gasket, o ring etc). A hard joint is typically a fastener joining metal with metal.
If you select the option SOFT the screwdriver will run the complete cycle at the selected speed.
If you select the option HARD the screwdriver will maintain the selected speed for a chosen time (brake
time) after the start and then the speed will be reduced automatically to apply a pre-torque before reaching
the final preset torque.
IMPORTANT: An incorrect selection of the joint type can result in inaccurate torque output.
BRAKE TIME: This option can be selected
U
only
U
in combination with the option HARD JOINT. You can
select a time between MIN (function excluded) and 10.0 seconds indicating how long the selected speed
(higher speed) will be on before switching to “pre-torque speed” (lower speed). The “pre-torque speed” will
be automatically chosen by the unit depending on the preset torque. The user cannot adjust the “pre-torque
speed”. CAUTION: The scope of the Brake Time is only to speed up the approach time in case of long
screws. Reaching the torque at higher speed will result in inaccurate torque output. To avoid inaccurate
torque we suggest selecting a shorter time, and then increase it step by step until finding the optimum time.
Documentation Provided By HMC Electronics
33 Springdale Ave. Canton, MA 02021
(800) 482-4440