INCRA Wonder Fence - Manual (Page 2)

2
Mounting Instructions for your InCra wonder Fence
Your new INCRA Wonder Fence can be used
either by clamping directly to the router table
(freestanding mode) or by attaching first to
your INCRA Jig Ultra (router table model) .
If you have purchased the TS/Wonder
Fence table saw fence upgrade kit, you’ll be
attaching the Wonder Fence directly to the TS
fence for use with your router table extension
wing . Find the instructions to follow that
cover your application .
Fig. 1 Attach table clamps
Freestanding Mode
(Shown in photo on front cover)
attach table clamps and
clamp to router table
Position the Wonder Fence on your
router table with the opening in the
fence centered on your router collet .
Loosen the
1 ⁄
4
-20 x 2" socket head
cap screw located on each of the (2)
table clamps using the supplied hex
tool . Now slide the rectangular nut
on the table clamp into the upper T-
slot on the rear of the Wonder Fence
(
Fig.-1) . Slide the table clamp to
the edge of your table and clamp in
place . Repeat for the second clamp at
the opposite edge of the router table .
Tighten both socket head cap screws
using the supplied hex tool .
Detail 1
Slide 1 ⁄ 4 -20
rectangular nut
into upper T-slot
safety
■
After making adjustments to the fence
positions, be sure to tighten the two
socket head cap screws through the
large holes in both the infeed and
outfeed fences .
■
When using fence settings in which the
router bit is partially recessed in the
fence opening, always insure that the
bit is centered within the opening .
■
Never let the router bit come into
contact with the aluminum body of the
INCRA Wonder Fence .
■ Whenever using large diameter
vertical or horizontal panel raising
bits or any other large diameter
bit, always follow that router bit
manufacturer’s operation and safety
recommendations .
■
Whenever it is necessary to remove
large amounts of stock, always use
multiple side-by-side passes to achieve
the final cut . Several shallow cuts are
safer and will yield better results .
Important safety instructions for using the INCRA Wonder Fence:
■
When using the INCRA TS/Wonder
Fence table saw fence upgrade kit
in conjunction with your INCRA-TS
table saw model, ALWAYS remove the
Wonder Fence before making any cuts
with your table saw blade .
■
Never attempt any cut with your table
saw blade while the Wonder Fence is
installed on your TS fence .
■
Before using the INCRA Wonder Fence,
read and follow all of the instructions
and safety information in this manual .
■ When using the INCRA Wonder
Fence in conjunction with any
other tool, first read and follow all
instructions and safety information in
that tool’s manual .
■
Use appropriate safety devices .
Always use a push stick, rubber
soled push block, or other safety
devices to keep your hands safely
away from the cutting tool .
■
When used in the free-standing
mode with the supplied table clamps,
always make sure the clamping
knobs are tightened securely in
place before making any cuts .
■
If attaching the INCRA Wonder
Fence to your INCRA Jig Ultra,
always make sure the carriage
clamp on the Incra Jig is in the
locked position and the base is
held securely in place before
making any cuts .
■
Always turn off the power and make
sure that the router bit has come to
a complete stop before changing
the setting of any part of the INCRA
Wonder Fence .
■
When adjusting the fence opening,
never position the infeed or outfeed
fence ends closer than
1 ⁄
8
" from the
router bit .
Detail 1 View from back of fence
nOTe: The table clamps are designed to
work on router tables from 1 1 ⁄
8
" to 1 3 ⁄
8
"
thick. To increase the thickness of a table
less than 1
1 ⁄
8 " thick, use double faced tape
to attach a wooden strip to the underside of
the table edge.
First:
Slide
table
clamp to
edge of
table
and
clamp
in place
Second:
Tighten
1 ⁄ 4 -20 x 2"
socket head
cap screw
The fence angle can be adjusted
perfectly square to your router table
by loosening the two phillips head
screws on the table clamps .