INCRA LS Positioner - Manual (Page 4)

4 INCRA Woodworking Tools & Precision Rules

Before using the INCRA LS Positioner, read and
follow all of the instructions and safety information
in this manual.

When using the INCRA LS Positioner in
conjunction with any other tool, first read and
follow all instructions and safety information in that
tool’s owner’s manual.

When mounted to a table surface, make sure that
all of the mounting screws are securely tightened
and the INCRA LS Positioner is firmly held in place.

Always turn off the power and make sure that the
bit or blade is fully stationary before moving the
INCRA LS Positioner to any new setting.

Always keep both hands behind the fence when
moving the INCRA LS Positioner to a new setting.

Before making a cut, always make sure that the
carriage clamp is fully engaged and the fence is
securely locked in place.

When using the INCRA LS Positioner with other
tools, make sure that all safety guards and other
safety equipment supplied by the manufacturer of
that tool are securely in place and functional. Never
let the INCRA LS Positioner interfere with another
tool’s safety equipment.

Use appropriate safety devices. Keep hands
clear of the bit or blade. Always use a push stick,
rubber soled push block, or other safety device to
keep your hands safely away from the cutting tool.

Wear safety glasses, hearing protection and
follow all normal shop safety practices.

DO NOT alter or modify the INCRA LS Positioner in
an attempt to use it with non-INCRA accessories.

Never let the bit or blade come into contact with
any part of the INCRA LS Positioner, INCRA Shop
Stop, or INCRA Right Angle Fixture.
SAFetY
GettInG ACquAInteD
Important safety instructions for using the InCrA lS Positioner
Before setting up and using your new INCRA LS Positioner, take a few moments to become better ac-
quainted with the tool by reviewing the following component descriptions and the illustration in Fig. 1.
 Lead Screw Positioning Element
The LS Positioner obtains its great accuracy and
repeatability from the precision lead screw, which
positions the fence in exact increments of 1 / 32 ”
(1mm metric version.)
 Auxiliary Scale Slots
Four auxiliary scale slots are provided to allow
additional setups and cutting operations to take
place without altering the primary scale position.
Simply slide the supplied 1 /
32
” or 1mm “floating”
scale into position as needed for reference.
The friction fit holds the scales securely during
cutting operations. These extra slots are great
for advanced joinery using the INCRA templates.
You can even leave your most frequently used
joinery templates from the optional INCRA Master
Reference Guide & Template Library permanently
installed.
 Three-Position Carriage Clamp
By pushing the carriage clamp down into the
“unlocked” position, the carriage is free to glide to
the next setting. Pull the clamp up to the center
position for micro adjusting. Pull the clamp up to
the final position and the carriage is locked solidly
in place.
 Hairline Cursor and View Windows
The large hairline cursor and view windows
provide a clear visual reference of the fence
location and span the width of the carriage top
and all five scale slots. The factory placement of
the cursor can be moved to the rear view window
location for use on smaller router tables.
 LS Base
The LS Base contains the threaded segment that
engages with and functions to locate the
carriage. It also houses the three-position carriage
clamp, the hairline cursor, and view windows.
 Carriage
The reinforced square tube design of the carriage
provides the ultimate in strength and support for
your fence. It supports the lead screw positioning
element and the micro adjust knob.
 Stainless Steel Primary Scale
After setting up your INCRA LS Positioner and
“zeroing” to the bit or blade, position this scale to
read 0” under the hairline cursor. Use this scale
as the primary source for readout of fence to bit or
blade distance.