Blizzard Lighting RGBAW ToughPar Zoom (Rev A) - Manual (Page 12)

Page 12
ToughPAR Zoom RGBAW Manual Rev. A Copyright (c) 2013 Blizzard Lighting, LLC
Setting the DMX Channel Mode:
To control the fixture with DMX, first select one of the DMX control channel modes (5/7/9 or 11ch.)
1.) To select a DMX channel mode, press the <MEnU> button, then use the <UP/DOWn> buttons until the
display reads
Chnd
and press the <EnTER> button.
2.) Then use the <UP/DOWn> buttons until the display reaches your desired channel mode.
3.) Push the <EnTER> button to confirm your choice.
Setting the DMX Address:
1.) Press the <MEnU> button, then use the <UP/DOWn> buttons until the display reads
Addr
and press
the <EnTER> button.
2.) Use the <UP/DOWn> buttons to set the appropriate DMX address from
001 -512
.
3.) Push the <EnTER> button to confirm your choice.
Auto Mode (Built-in Programs):
1.) Press the <MEnU> button, then use the <UP/DOWn> buttons until the display reads
AUTO
, and press
the <EnTER> button.
2.) Then use the <UP/DOWn> buttons to choose your desired program from
AT01-AT10,
and press the
<EnTER> button. Notice that you can now adjust the chase speed:
SP--.
3.) Use the <UP/DOWn> buttons to set your desired speed from
000
to
255
(fast <--> slow).
4.) Push the <EnTER> button to confirm your choice.
Custom Color Adjustments:
1.) Press the <MEnU> button until the display reads
STAT
and press the <EnTER> button.
2.) Press the <UP/DOWn> buttons until the display reads
RED
(Red intensity, 0-255),
GREN
(Green inten-
sity, 0-255),
BLUE
(Blue intensity, 0-255),
WHIT
(White intensity, 0-255), or
AMB
(Amber intensity, 0-255)
and adjust to your desired values. Push the <EnTER> button to confirm.
3.) Push the <EnTER> button to confirm.
Note: These settings will effect the fixture GLOBALLY, IE in any mode.
32-Bit Dimmer Mode Settings:
• Dimming Mode 1 = 32-bit, 0-25% intensity range
• Dimming Mode 2 = 32-bit, 0-50% intensity range
• Dimming Mode 3 = 32-bit, 0-75% intensity range
• Dimming Mode 4 = 32-bit, full intensity dimming
1.) Press the <MEnU> button, then use the <UP/DOWn> buttons until the display reads
DIM
and press
the <EnTER> button
.
2.) Then use the <UP/DOWn> buttons to choose from
DIM1
to
DIM4
.
4.) Push the <EnTER> button to confirm your choice.
Color Temperature-Based White Balance:
This is used to setup and store up to 10 separate custom white balance settings using R/G/B/A/W values.
1.) Press the <MEnU> button, then use the <UP/DOWn> buttons until the display reads
WTST
and press
the <EnTER> button
.
2.) Then use the <UP/DOWn> buttons to choose from
WT01
to
WT10
and press the <EnTER> button.
3.) Press the <UP/DOWn> buttons until the display reads
RED
(Red intensity, 0-255),
GREN
(Green inten-
sity, 0-255),
BLUE
(Blue intensity, 0-255),
WHIT
(White intensity, 0-255), or
AMB
(Amber intensity, 0-255)
and adjust to your desired values.
4.) Push the <EnTER> button to confirm your choice.