E-flite Apprentice S 15e RTF with SAFE - Manual (Page 23)

EN
Optional Transmitter Setup
Buddy Box Setup
Transmitter Gear/
Ch 5 Aux 1 Flight Mode/ Panic Switch
SAFE Flight Modes
Supported
Panic Recovery
Switch
SAFE Flight Mode
Switch
Throttle, Aileron, Elevator and Rudder are in Normal position.
DX4e (2pos)
N N/A Default 2 pos Trainer ACT / AUX
DX4e (3pos) N N/A Default 3 pos Trainer Ch 5
DX5e (2pos) N N/A Default 2 pos Trainer Ch 5
DX5e (3pos) N N/A Default 3 pos Trainer Ch 5
DX6i R N * (Flap System) Norm £ 100 Land  100 2 pos Flaps GEAR / F MODE
DX6 N R * (Channel Input Config) Gear is B, Aux1 is switch i 3 pos Bind / i B
DX7 N N
* (Flap System) Norm  100, Mid  100, Land £ 100
(3 pos Aux1 switch–0 & 1 are normal 2 is panic)
2 pos Flap GEAR
DX7s N R * (Switch Select) Gear to INH, FM to INH, Flap to Gear, Trainer to Aux1 3 pos Trainer Flap
DX8 N R * (Switch Select) Gear to INH, FM to Gear, Flap to INH, Trainer to Aux 1 3 pos Trainer F MODE
DX9 N R * (Channel Input Config) Gear is B, Aux1 is switch i 3 pos Bind / i B
DX10t N R * (Channel Input Config) Gear is A, Aux1 is R stick 3 pos R-Tip A
DX18 N R * (Channel Input Config) Gear is B, Aux1 is switch i 3 pos Bind / i B
N = Normal R = Reverse
Master Transmitter Setup Slave Transmitter Setup
Master Transmitter Master Setup Slave Transmitter Slave Setup
DX4e (2pos) Factory Trainer Settings DX4e (2pos) Factory Trainer Settings
DX4e (3pos) Factory Trainer Settings DX4e (3pos) Factory Trainer Settings
DX5e (2pos) Factory Trainer Settings DX5e (2pos) Factory Trainer Settings
DX5e (3pos) Factory Trainer Settings DX5e (3pos) Factory Trainer Settings
DX6i Factory Trainer Settings DX6i Factory Trainer Settings
DX6
Activate Programmable Master and insure
channels Thro - Aux 1 are set to slave
DX6 Factory Trainer Settings
DX7 Trainer to Normal DX7 Factory Trainer Settings
DX7s
Activate Programmable Master and insure
channels Thro - Aux 1 are set to slave
DX7s Factory Trainer Settings
DX8
Activate Programmable Master and insure
channels Thro - Aux 1 are set to slave
DX8 Factory Trainer Settings
DX9
Activate Programmable Master and insure
channels Thro - Aux 1 are set to slave
DX9 Factory Trainer Settings
DX10t
Activate Programmable Master and insure
channels Thro - Aux 1 are set to slave
DX10t Factory Trainer Settings
DX18
Activate Programmable Master and insure
channels Thro - Aux 1 are set to slave
DX18 Factory Trainer Settings
If using any DSMX transmitter other than the included DX5e (3 pos gear
switch) the radio will have to be configured correctly for the SAFE system to
work properly.
• SAFE Flight mode is selected using Channel 5 signal (high, middle, low)
• Panic mode is selected with Channel 6 signal (high, low)
Refer to your transmitter’s manual for more information about transmitter
setup.
Refer to the Receiver Setup section of this manual to select the SAFE Flight
modes you desire to use on a transmitter with only a 2 position Channel 5
switch.
IMPORTANT: If using the buddy box option for training on a transmitter
other than the included DX5e use these settings for a Master and or Slave
Transmitter. Failure to do so will not allow SAFE technology Flight modes to
work correctly.
IMPORTANT: If using the buddy box option the transmitter must be configured
using the Transmitter Setup and Buddy Box setup charts.
23