GBC H925 - Manual (Page 2)

2 3
A) Feed Tray
Plateau d’alimentation
Bandeja de alimentación
B) Paper Side Guide
Guide latéral pour le papier
Guía lateral del papel
C) Top Cover
Couvercle supérieur
Tapa superior
D) Control Panel
Panneau de commande
Panel de control
E) Exit Tray
Plateau de sortie
Bandeja de salida
F) Power Button
Touche d’alimentation
Botón de encendido
G) 4 EZload TM Levers
4 leviers de chargement EZload TM
4 palancas de carga EZload TM
H) Heat Button
Touche de chauffage
Botón “Heat” (de calentamiento)
I) Feed Switch
Interrupteur d’alimentation
Interruptor “Feed” (de alimentación)
J) Idler Bar Assembly
Assemblage de barre de transfert
Conjunto de barra intermediaria
K) Heat Shoe
Sabot chauffant
Zapata térmica
L) Film Roll
Rouleau de pellicule
Rollo de película
M) Ready (LED)
Voyant d’état « Prêt » (DEL)
LED “Ready” (Lista)
N) Power
Voyant d’alimentation
Encendido
O) Start Button
Touche de démarrage
Botón “Start” (Inicio)
P) Alert (LED)
Voyant d’alerte (DEL)
LED “Alert” (Alerta)
Q) Low Film (LED)
Voyant de faible quantité
de pellicule (DEL)
LED “Low Film” (Poca
película remanente)
R) Stop Button
Bouton d’arrêt
Botón de Paro
S) Film Select Buttons
Touches de sélection de
pellicule
Botones de selección de
película
HeatSeal Sprint H925 - Description/
Description/Descripción
TM ® HeatSeal Sprint H925 - Safety TM ®
Important Safety Instructions Important Safeguards
YOUR SAFETY AS WELL AS THE SAFETY OF OTHERS IS IMPORTANT
TO GBC. IN THIS INSTRUCTION MANUAL AND ON THE PRODUCT ARE
IMPORTANT SAFETY MESSAGES. READ THESE MESSAGES CAREFULLY.
ON THE PRODUCT YOU WILL FIND IMPORTANT SAFETY MESSAGES.
READ THESE MESSAGES AND INSTRUCTIONS CAREFULLY.
SAVE THESE INSTRUCTIONS FOR LATER USE.
THE FOLLOWING WARNINGS ARE FOUND ON THIS PRODUCT.
This safety message means that you could be seriously hurt or killed
if you open the product and expose yourself to hazardous voltage.
Do not touch heat shoes until they have cooled.
• Use this laminator only for its intended purposes as according
to the specifications outlined in the operating instructions.
• Keep hands, long hair, loose clothing and articles such as
necklaces or ties away from the front of the pull rollers to avoid
entanglement and entrapment.
• Avoid contact with the heat shoes during operation or shortly
after the laminator has been turned off. The heat shoes can reach
temperatures in excess of 300°F.
• Keep hands and fingers away from the path of the sharp film
cutter blade located at the film exit.
• Place the laminator on a stable cart, stand or table capable of
supporting at least 110 lbs/50 kg. An unstable surface may cause
the laminator to fall resulting in serious bodily injury. Avoid quick
stops, excessive force and uneven floor surfaces when moving
the laminator on a cart or stand.
• Do not defeat or remove electrical and mechanical safety
equipment such as interlocks, shields and guards.
• Do not insert objects unsuitable for lamination.
• Do not expose laminator to liquids.
• This laminator must be connected to a supply voltage correspon-
ding to the electrical rating as indicated on the serial plate located
on the rear of the machine.
• Unplug the laminator before moving it, or when it is not in use for
an extended period of time.
• Do not operate the laminator with a damaged power supply cord
or plug.
• Do not overload electrical outlets as this can result in fire or shock.
• Do not alter the attachment plug. This plug is configured for the
appropriate electrical supply.
• The unit is intended for indoor use only.
• Disconnect the attachment plug from the receptacle to which it is
connected and keep the power supply cord in your possession
while moving the laminator.
• Do not operate the laminator with a damaged power supply
cord or attachment plug, upon occurrence of a malfunction, or
after laminator has been damaged. Contact an authorized GBC
service representative for assistance.
This safety message means that you could cut yourself if you
are not careful.
THE SAFETY ALERT SYMBOL PRECEDES EACH SAFETY
MESSAGE IN THIS INSTRUCTION MANUAL.
WARNING: THE SAFETY ALERT SYMBOL PRECEDES EACH
SAFETY MESSAGE IN THIS INSTRUCTION MANUAL THIS
SYMBOL INDICATES A POTENTIAL PERSONAL SAFETY
HAZARD THAT COULD HURT YOU OR OTHERS.
WARNING: DO NOT ATTEMPT TO SERVICE OR REPAIR
THE LAMINATOR.
WARNING: DO NOT CONNECT THE LAMINATOR TO AN
ELECTRICAL SUPPLY OR ATTEMPT TO OPERATE THE
LAMINATOR UNTIL YOU HAVE COMPLETELY READ THESE
INSTRUCTIONS. MAINTAIN THESE INSTRUCTIONS IN A
CONVENIENT LOCATION FOR FUTURE REFERENCE.
WARNING
Electrical shock hazard.
Do not open. No user
serviceable parts inside.
Refer servicing to qualified
service personnel.
CAUTION
Hot
surface.
CAUTION
SHARP BLADE.
Keep hand and
fingers away.
WARNING: FOR YOUR PROTECTION, DO NOT CONNECT
THE LAMINATOR TO ELECTRICAL POWER OR ATTEMPT
TO OPERATE UNTIL YOU READ THESE INSTRUCTIONS
COMPLETELY. KEEP OPERATING INSTRUCTIONS IN A
CONVENIENT LOCATION FOR FUTURE REFERENCE. TO
GUARD AGAINST INJURY, THE FOLLOWING BASIC SAFETY
PRECAUTIONS MUST BE OBSERVED IN THE SET-UP AND
USE OF THE LAMINATOR.
CAUTION: The receptacle must be located near the equipment
and easily accessible. Do not use an extension cord.
General Safeguards
Electrical Safeguards
limenta
B
A
C
D
E
S
O
M
N
P
Q
F
G
H
I
J
L
K
R
Start/Start/Inicio Stop/Stop/Interrupción
3 mil / 75 mic 5 mil / 125 mic