GBC H75 HeatSeal - Manual (Page 2)

HeatSeal ™ H65 / H75
4
╞
5
Electrical safeguards
• The unit must be connected to a supply voltage corresponding to the
electrical rating shown on the unit.
• Unplug the unit before moving it, or when it is not in use for an
extended period of time.
• Do not operate with a damaged supply cord or plug. Do not alter the
attachment plug. The plug is configured for the appropriate electrical
supply.
• Do not overload electrical outlets beyond their capacity; fire or
electrical shock could result.
• The unit is intended for indoor use only.
• Never push objects through the cabinet slots. Do not spill liquid of
any kind on this product.
• Close supervision is required when this product is used near
children.
Service
• Do not attempt to service or repair the pouch laminator yourself.
Unplug the unit and contact an authorized GBC service
representative for any required repairs.
Cleaning
General safeguards
• Use the unit only for its intended purposes of laminating documents.
• Do not place anything in the throat opening of the laminator other
than pouches/documents.
• Place unit on a secure, stable work area to prevent the unit from
falling and possibly causing personal injury and damage to the unit.
• Follow all warnings and instructions marked on the unit.
• The socket outlet shall be installed near the equipment and shall be
easily accessible.
Safety instructions
YOUR SAFETY AS WELL AS THE SAFETY OF OTHERS IS IMPORTANT
TO GBC. IN THIS INSTRUCTION MANUAL AND ON THE PRODUCT ARE
IMPORTANT SAFETY MESSAGES. READ THESE MESSAGES CAREFULLY.
THE FOLLOWING WARNING IS FOUND ON THE BOTTOM OF THE
PRODUCT.
This safety message means that you could be seriously hurt or killed if
you open the product and expose yourself to hazardous voltage.
The following ISO and IEC symbols appear on this product, and their
meaning is as follows:
Electrical shock hazard.
Do not open. No user
servicable parts inside.
Refer servicing to qualified
service personnel.
WARNING
Caution: Unplug this product before cleaning.
ƽ
THE SAFETY ALERT SYMBOL PRECEDES EACH SAFETY
MESSAGE IN THIS INSTRUCTION MANUAL.
THIS SYMBOL INDICATES A POTENTIAL PERSONAL
SAFETY HAZARD THAT COULD HURT YOU OR OTHERS,
AS WELL AS CAUSE PRODUCT DAMAGE OR PROPERTY
DAMAGE.
ƽ
WARNING: FOR YOUR PROTECTION DO NOT CONNECT
THE POUCH LAMINATOR TO ELECTRICAL POWER UNTIL
YOU READ THESE INSTRUCTIONS COMPLETELY. KEEP
THESE INSTRUCTIONS IN A CONVENIENT LOCATION
FOR FUTURE REFERENCE. TO GUARD AGAINST INJURY,
THE FOLLOWING BASIC SAFETY PRECAUTIONS MUST
BE OBSERVED IN THE SET-UP AND USE OF THIS
PRODUCT.
ƽ
Ꮨ ƽ
ƽ
Important safeguards
ƽ
• Wipe exterior only with a damp cloth. Do not use detergents or
solvents.
Special notice
Thank you, for your recent purchase of a GBC Pouch Laminator.
Your new laminator may emit a slight odour during the initial stage
of operation. It is normal and will diminish after several hours of
operation.
Off
Ready
On
Std. Paper
Photo Paper
Guarantee
Operation of this machine is guaranteed for two years from date of
purchase, subject to normal use. Within the guarantee period, GBC will
at its own discretion either repair or replace the defective machine free
of charge. Defects due to misuse or use for inappropriate purposes are
not covered under the guarantee. Proof of date of purchase will be
required. Repairs or alterations made by persons not authorised by
GBC will invalidate the guarantee. It is our aim to ensure that our
products perform to the specifications stated. This guarantee does not
affect the legal rights which consumers have under applicable national
legislation governing the sale of goods.
2b 1
4 5
6 8 7
3
2a
On Off
On Off
Operating instructions
Specifications
Electrical
Machine Dimensions
Machine Weight
Maximum Pouch Width
Maximum Pouch Thickness
Maximum Thru-put Thickness
Warm-Up Time (2 x 75 mic.)
GBC HeatSeal H65
230v / 50 Hz / 0.65 Amps / 150 W
362 x 108 x 102mm
2.5 kg
241mm
2 x 125 mic (Total 250)
0.8mm
8 minutes
Connect power cord to appropriate power source.
GBC Heatseal H65/H75 Laminator is designed for 2 x 75 micron
(total 150) up to 2 x 125 micron (total 250) pouches.
Choose the right setting (fig. 1).
The laminator has 2 temperature settings positioned on the front:
‘Std. Paper’– when laminating with Standard paper
(less than 200 g per sq. metre)
‘Photo paper’– when laminating with Photo paper
(more than 200 g per sq. metre)
Push the switch located on the right side to “On” (I) (fig. 2a). The
red “Power” indicator lamp will illuminate (fig. 2b).
The “Ready” indicator lamp will glow green when the laminator
reaches lamination temperature (fig. 3).
Note: It is normal for the Ready Light to cycle On and OFF after
initial warm up. You can continue laminating.
Position the paper to be laminated into a GBC laminating pouch,
so that the document is aligned to the folded edge and right and
left borders are equal (fig. 4).
Insert the pouch and its content straight into the machine, leading
with the folded edge (fig. 5).
The laminated item will automatically exit at the rear of the pouch
laminator (fig. 6). Immediately after the pouch has stopped moving,
place it on a flat surface to cool for one minute before handling.
If you have finished laminating, then move the switch to the "off"
(0) position (fig. 7).
Do not laminate an empty pouch.
To correct misfeeds, press and hold the release button
(fig. 8), located at the back of the machine, while pulling
the misfed material out of the laminator.
Register this product online at www.gbceurope.com
1
2
3
4
5
6
7
Helpful laminating hints
As soon as the lamination is completed, remove from the rear of
the machine and place on a cool flat surface for cooling to prevent
the pouch from curling.
If the laminated item appears to be cloudy, it means that the
laminator temperature is not hot enough. Allow the laminator to
heat for a few more minutes then run the pouch through again.
If the laminated item is wavy, the laminator is too hot. Verify
temperature selector is set at the appropriate temperature.
Do not attempt to do single sided lamination. This will destroy the
laminator.
Do not block the vent slots, this will cause the laminator to
overheat.
Before laminating important or unique documents always run a test
pouch through the laminator using a similar type document.
1
2
3
4
5
GBC HeatSeal H75
230v / 50 Hz / 0.87Amps / 200 W
451 x 108 x 102mm
3.0 kg
318mm
2 x 125 mic (Total 250)
0.8mm
8 minutes
Standard Paper
( < 200 g/m
2 )
Photo Paper
( > 200 g/m
2 )
If the laminated item appears to be cloudy,
choose the setting
If the laminated item is wavy, choose the setting
Min Max
2 x 75 mic. 2 x 125 mic.
(Total 150) (Total 250)
Photo Paper Std. Paper
Photo Paper
Std. Paper
Min Max
2 x 75 mic. 2 x 125 mic.
(Total 150) (Total 250)