Nipros ST-7J User Manual

St-7j, Power off on, Shoulder adaptor

Advertising
background image

For using ST-7J.
Please read this manual thoroughly before operating the unit.

■ Operation

■Specifications

■Outside dimensions

2. Fix the handle of ST-7J to the screw hole
on the upper side of the grip of AG-HPX175,
AG-HMC155/151 with the supplied screw.

3. If the power is supplied to a camera from
ST-7J, please use the optional power cable
DC-P175(for AG-HPX175) or DC-P155(for
AG-HMC155/151).

4. Install a lithium-ion battery to the rear of
ST-7J.

6. Conversion cables which are supplied to
a camera can be connected with the BNC-
BNC relay connector.

7. ST-7J can be installed to the Panasonic
tripod base SHAN-TM700 to install to a
tripod.

5. Turn on the POWER SW on the bottom of the
rear of ST-7J. LED indicator lights up and the
power is supplied to a camera and a light.

ST-7J

Shoulder Adaptor

■ To use for AG-HMC155

POWER

OFF

ON

240

153

449

■ Attaching the handle

POWER

OFF

ON

Operating

Instructions

■ Caution : They might damage the grip portion of a camera if you lift a camera up with
only the grip portion or install a receiver of the wireless microphone, a hard disk back
up unit, etc. to the battery shoe of ST-7J.

A small camera applicable to ST-7J is designed to be used as it is. We recommend
you to use ST-7J as a support equipment. It is not applied to the operation which
gives a big weight pressure to the grip portion and the application to use a wireless
receiver and a hard disk back up unit together.

■ Main Features :

ST-7J is applicable to a handy type camera:( AG-HPX175, AG-HMC155/151) etc.

Fit the handle to the ST-7J main body
with four screw holes and tighten withg
the supplied M3 screws.

When ST-7J is used for AG-HMC155,
take off the handle from the stay and
replace it to the lower screw holes of
the stay.

DC IN DC 12 V XLR 4-pin( Male ) × 1

V-shoe mount

(

Li-ion Battery Input) × 1

DC OUT DC 12 V XLR 4-pin(Female) × 1

DC 12/8.4 V Mini 4-pin(Female) × 1

Extension terminal BNC-BNC × 3

1/4 in. camera screw × 1 with rotation prevention × 1

1/4 in. camera screw × 1 Spare

Shoulder pad Just fit shoulder pad

Operating temperature 0℃ to +40℃

Storage temperature -20℃ to +60℃

Outside dimensions

153 Ч 240 Ч 449 mm(W×H×D)

Weight approx. 1.5 kg


■ DC OUT CONNECTOR

1

2

3

4

DC12V(G)

DC8.4V(G)

DC8.4V(+)

DC12V(+)

To supply a power of +8.4 V
for a camera and a power of
+12 V for a wireless receiver.

for AG-HPX175(default)

for AG-HMC155

Stay

Handle

for AG-HPX175(default)

for AG-HMC155

1.Install ST-7J to the bottom of a handy
camera with the guide pin. And tighten the
camera screw to fit it to a camera.

ST-7J

Spare screw
with washer

Camera screw
with washer

Guide

pin

Camera

screw

Spare

screw

Washer

Camera

screw

Guide pin

plate

ST-7J

take off

remove

install

ST-7J

Fit the washer
to each screw.

For a camera which has two screw holes

1 Take off the guide pin plate from the ST-7J loosening

the camera screw and remove the camera screw from

the guide pin plate. Fit the washers(supplied) to the

spare screw (supplied) and the camera screw.

2 Install the screws with the washers to the ST-7J and fix

the ST-7J into the screw holes of a camcorder with the

two screws.

1

2

NIPROS accept no liability whatever for damages arising from improper use not conforming to the
instructions in the instruction manuals.

NIPROS accept no liability whatever for incidental damages arising out of the use or inability to use
the product, including, but not limited to, damage to the camera, etc., corruption or loss of data, lost
business revenue or suspension of business operations.

NOTE

Features, design and specifications are subject to change without notice.

* The protection circuit is equipped

so that the MINI 4-pin(Female)

connector can continue to supply

the power to a camcorder even if

the XLR 4-pin output is shorted

or troubled.

TM

Advertising