Cambridge Audio 540D V2 - Manual (Page 17)

540D V2 azur
17
ENGLISH
There is no power
Ensure the AC power cord is connected securely.
Ensure the plug is fully inserted into the wall socket and is switched on.
Check fuse in the mains plug or adaptor.
The player will not read the disc
Check the disc is not loaded upside down.
Check that the disc is not too scratched or dirty.
The disc type is unsupported by this unit (e.g. MP3, DVD-A, SACD etc).
There is no sound
Ensure that the amplifier is set correctly.
Check that the interconnects are inserted correctly.
The disc is skipping
Check that the disc is not too scratched or dirty.
Ensure the player is on a firm surface and not subject to vibrations.
A low hum or buzz sound can be heard
Power cords or lighting placed near this product.
Analog inputs not connected securely.
No sound from the rear speakers
Source being played is not recorded in surround-sound.
A stereo mode has been selected.
No sound from the centre speaker
A stereo mode has been selected.
No sound from the subwoofer
DD PLII mode (which has no LFE channel) has been selected with all
speakers set to ‘Large’.
Remote control is not working
The batteries are flat.
The remote is too far from the unit or out of the effective range.
Troubleshooting
The 540D V2 features a Control Bus input/output
that allow un-modulated remote control
commands (positive logic, TTL level) to be received
electrically by the unit and looped to another unit
if desired. These control commands are typically
generated by custom installation (multi-room)
systems or remote IR receiver systems. The Control Bus sockets are
colour-coded orange.
An IR Emitter Input is also provided that allows modulated IR remote
control commands to be received electrically by the unit. Commands on
this input operate the unit only and are not looped out demodulated on
the Control Bus Output. This feature is useful for multi-room systems
(such as the Cambridge Audio Incognito multi-room system) which
feature routed I.R. emitter outputs. Instead of using window emitters
stuck over the CD players front panel IR receiver, a mono 3.5mm mini-
jack to 3.5mm mini-jack lead can be used for a more reliable electrical
connection.
The 540D V2 also features a ‘direct’ IR/Control code for On/Off that can
be accessed on the supplied remote control for teaching into C.I.
systems as follows:
Press and hold the Standby button. The remote first generates it's
standby (toggle) command. Keep the button held down, after 12
seconds a DVD player “On” command will be generated. If the button is
kept held down for a further 12 seconds, a DVD player “Off” command
is generated.
A full code table for this product is available on the Cambridge Audio
website at: www.cambridge-aaudio.com
Custom installation (C.I.) use
IR Emitter
In In Out
Control Bus
Disc types CD (CD-DA), DVD-V, CD-R/RW,
DVD-R/RW, DVD+R/RW, DivX, MP4
DAC architecture Crystal/Cirrus Logic CS4382
8-channel (5.1 + 2ch Stereo) 24 Bit
Analog audio outputs • Stereo
• 5.1 (from DD or PLII)
Analog video outputs • Composite Video (CVBS)
• S-Video (SVHS)
• RGB/SCART
• Component (YCbCr/YPbPr)
HDMI output Scaling/Deinterlacing to 480p, 576p,
720i/p, 1080i
THD (unweighted) < 0.002% @ 1kHz
< 0.008% @ 20Hz - 20kHz
IMD (19/20kHz) 0dBFs < 0.002%
S/N ratio < -103dB
Crosstalk @1kHz < -103dB @ 1kHz
Dynamic Range > 105dB
Frequency response 5Hz - 20kHz ± 0.2dB
Jitter (correlated) < 140 psec
Composite Video 1.0V pk-pk (75 ohms)
S-VVideo Y: 1.0V pk-pk (75 ohms)
C: 0.286V pk-pk (75 ohms)
Component Video Y: 1.0V pk-pk (75 ohms)
Cb/Cr: 0.75V pk-pk (75 ohms)
Pb/Pr: 0.75V pk-pk (75 ohms)
Power supply 100-240V AC ~ 50/60Hz
Max power consumption 25W
Dimensions (H x W x D) 70 x 430 x 310mm
Weight 3.8kg (8.4Lbs)
Technical specifications