Craftsman 316.79192 - Manual (Page 9)

3. Wash the filter in
detergent and water
(Fig. 19). Rinse the filter
thoroughly. Squeeze
out excess water. Allow
it to dry completely.
4. Apply enough clean SAE
30 oil to lightly coat the
filter (Fig. 20).
5. Squeeze the filter to
spread and remove
excess oil (Fig. 21).
6. Replace the air filter
inside the air filter/muffler
cover (Fig. 18).
Reinstalling the Air Filter/Muffler
Cover
1. Place the air filter/muffler cover
over the back of the carburetor
and muffler. Align the screw holes.
2. Insert the four (4) screws into the
holes in the air filter/muffler cover
(Fig. 17) and tighten. Do not over
tighten.
SPARK ARRESTOR MAINTENANCE
NOTE: Pay close attention when disassembling the muffler so
you can put it back together correctly. Failure to do so will
damage the unit and may cause serious personal injury.
1. Remove air filter/muffler cover. Refer to Removing the Air
Filter/Muffler Cover (p. 9).
2. Locate the muffler, but do not remove it. Find the screw on
the bottom of the muffler (Fig. 22). This screw holds the
Spark Arrestor Hood Assembly and the spark arrestor
screen to the bottom of the muffler. Remove this screw
using either a Torx T20 or flat blade screwdriver.
3. Using a small flat blade screwdriver, carefully pry up the
spark arrestor screen from the recessed hole, taking care to
notice that the “raised” part of the spark arrestor screen is
inside the recessed hole. Remove the spark arrestor screen
from the
muffler.
4. Clean the spark
arrestor screen
with a wire
brush. Replace
it if it is
damaged, or if
you are unable
to clean it
thoroughly.
9
MAINTENANCE & REPAIR INSTRUCTIONS
AIR FILTER MAINTENANCE
Removing the Air Filter/Muffler Cover
1. Remove the four (4) screws
securing the air filter/muffler
cover (Fig. 17). Use a flat
blade or T20 Torx bit
screwdriver.
2. Pull the cover from the
engine. Do not force.
Cleaning the Air Filter
Failure to maintain your air
filter properly can result in poor
performance or can cause
permanent damage to your
engine.
1. Remove air filter/muffler
cover. Refer to Removing
the Air Filter/Muffler Cover
above.
2. Turn cover over and look inside to locate the air filter.
Remove the air filter from inside the air filter/muffler cover
(Fig. 18).
WARNING: To avoid serious personal injury,
always turn your unit off and allow it to cool before
you clean or service it.
Fig. 19 Fig. 20
Fig. 21
Air Filter
Inside Muffler
Cover
Fig. 18
Screws
Fig. 17
Fig. 22
Spark Arrestor
Screen
Spark Arrestor
Hood
Screw
Muffler
To Engine
Tabs
Slots
FREQUENCY MAINTENANCE REQUIRED SEE
Before starting
engine
Fill fuel tank with fresh fuel p. 6
Every 10 hours Clean and re-oil air filter p. 9
Every 25 hours
Check and clean spark arrestor
Check spark plug condition and gap p. 9
p. 10
Every 50 hours
Inspect exhaust port and spark
arrestor screen for clogging or
obstruction
p. 9
MAINTENANCE SCHEDULE
Perform these required maintenance procedures at the
frequency stated in the table. These procedures should also be
a part of any seasonal tune-up.
NOTE: Maintenance, replacement, or repair of the emission
control devices and system may be performed by a Sears
or other qualified service dealer. Call 1-800-4-MY-HOME
®
for more information.
In order to assure peak performance of your engine, inspection
of the engine exhaust port may be necessary after 50 hours of
operation. If you notice lost RPM, poor performance or general
lack of acceleration, this service may be required. If you feel
your engine is in need of this inspection, refer service to a
Sears or other qualified service dealer. Call 1-800-4-MY-
HOME
® for more information. DO NOT attempt to perform this
process yourself as engine damage may result from
contaminants involved in the cleaning process for the port.
WARNING: To prevent serious injury, never
perform maintenance or repairs with unit running.
Always service and repair a cool unit. Disconnect the
spark plug wire to ensure that the unit cannot start.