Document Outline

• BROADway Installation Manual
• Preface
  • Compliance
    • Safety of Information Technology Equipment
    • FCC Requirements, Part 15
    • FCC Requirements, Part 68
    • Industry Canada ICES-003
    • Industry Canada CS-03
  • Safety Information
  • Notices
  • Electrostatic Discharge (ESD) Precautions
  • Warranty
    • Limitation of Warranty & Limitation of Remedies
    • Warranty Product Returns
  • Third-Party Software Notices
    • Sun Microsystems, Inc., Software Notice
• Table of Contents
• 1 - Introduction
  • Overview
• 2 - Installation
  • Overview
  • Chassis Overview
  • Mounting the Chassis in a Rack
  • Cabling Power and Ground
  • Cabling the Serial Craft Port
  • Cabling the Ethernet Port
  • Cabling the Network Synchronization Port
    • Cabling the Clock Ports on the BITS Chassis
    • Cabling the Clock Ports on the ITU Chassis
  • Cabling the Alarm Ports
    • Alarm Input Sensing
    • Alarm Output Reporting
    • Alarm Cut Off (ACO)
  • Installing the NSP101 Control Card
  • Installing the NIP400 Line Interface Card
    • Cabling the NIP400
    • NIP400 LED Indicators
  • Installing the NHP160 Line Interface Card
    • Cabling and Inserting the NHP160 Line Interface Card
    • NHP160 LED Indicators
  • Installing the BSP200 Line Interface Card
    • Cabling the BSP200
    • BSP200 LED Indicators
  • Installing OSP155/ESP155/BCP155 Line Interface Cards
    • Cabling the OSP155 and BCP155
    • Cabling the ESP155
    • OSP155, BCP155, and ESP155 LED Indicators
  • Attaching the Front Panel
  • Applying Power to the Chassis
  • Maintaining BROADway Hardware
    • Installing New Cards
      • Installing a Redundant NSP101 Card
      • Installing Additional NIP400 Cards
      • Installing Additional NHP160 Cards
      • Installing Additional BSP200 Cards
      • Installing Additional OSP155, ESP155 or BCP155 Cards
    • Replacing Failed Cards
      • To Replace an NSP101 Card
      • To Replace a NIP400 Card
      • To Replace an NHP160 Card
      • To Replace a BSP200 Card
      • To Replace a BCP155, OSP155, or ESP155 Card
    • Maintaining the Fan Tray
• 3 - Configuration
  • Overview
  • Assigning an IP Address to the BROADway System
    • Default BROADway IP Address
    • Assigning a Different IP Address
      • Creating a Bridge Virtual Interface (BVI)
  • Management Access to the BROADway System
    • Viewing Serial Craft Port Settings With the GUI
    • Local SCP-1 Serial Craft Port Access
    • Remote Modem SCP-1 Serial Craft Port Access
    • Ethernet Port Command Line Access
    • Ethernet Port Web Browser GUI Access
  • Logging In With the Web Browser Interface (GUI)
  • Logging In With the Command Line Interface (CLI)
  • Setting Up User Accounts
    • User Account Management Using the GUI
    • User Account Management Using TL1
      • Viewing Existing User Accounts
      • Creating New User Accounts
      • Editing User Accounts
      • Deleting User Accounts
  • Changing Your Password
    • Changing Your Password Using the GUI
    • Changing Your Password Using TL1
  • Setting the System Date and Time
    • Setting the Date and Time Using the GUI
    • Setting the Date and Time Using TL1
  • Setting System Node Parameters
    • Setting System Node Parameters Using the GUI
    • Setting System Node Parameters Using TL1
  • Managing the BROADway Configuration Database
    • Managing the Database Using the GUI
    • Managing the Database Using TL1
    • Exporting the BROADway Database to a TL1 Script
    • Copying Files Between NSP101 Controllers
    • Re-Starting the BROADway System Using TL1
  • Using FTP with the BROADway System
  • Upgrading System Software
    • Rolling Back a Software Update
    • Upgrading the Boot ROM
    • TL1 Software Upgrade Commands
• A - Ports and Cables
  • Overview
  • SCP-1 and SCP-2 Connector Pinouts
  • ETH-1 and ETH-2 Connector Pinouts
  • CKIN-1 and CKIN-2 Connector Pinouts (BITS Only)
  • NIP400 Connector Pinouts (NIP TX1-RX1, NIP TX2-RX2)
  • ALARMS Connector Pinouts
  • NHP160 Connector Pinouts
• Index