FRIGIDAIRE FFRG1001PW - Manual (Page 3)

Specifications
subject to change.
Specifications
subject to change.
USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com
CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca
FFRG1001P 10/13 © 2013 Electrolux Home Products, Inc.
Dryer
FFRG1001PW 7.0 Cu. Ft. D.O.E. Gas
Top Load Dryer Specifications
• Product Shipping Weight (approx.) – 143 Lbs.
• Designed for HOME USE only, not recommended for commercial
application.
• Always consult local and national electric & gas codes.
• Electrical supply with grounded three-prong receptacle is required.
Power supply circuit must be installed in accordance with current
edition of National Electrical Code (ANSI/NFPA 70) and local codes
& ordinances. (Do not use same circuit as washer.)
• Gas supply line should be 1/2" black iron, stainless steel, or plastic-
coated brass pipe and MUST have individual shutoff valve, located
within 6 feet of dryer. Gas supply line must be installed in accordance
with current edition of National Fuel Gas Code (ANSI Z223.1) and
local codes & ordinances.
• Voltage Rating – 120V / 60 Hz / 15 Amps
• Amps @ 120 Volts = 9.0 Amps
• Connected Load (kW Rating) @ 120 Volts = 4.0 kW
• Equipped with 120V 3-wire power supply cord, approx. 60" long.
• Dryer can be installed in recess or closet requiring 0" minimum
installation clearance around sides and back of unit. To achieve
0" minimum rear clearance, dryer MUST be vented straight back.
Closet installation requires additional 1" minimum clearance between
front of unit and vented door. Door MUST be vented with 120 sq. in.
minimum louvered opening, equally divided, located 3" from top and
bottom of door. A louvered door with equivalent air openings for full-
length of door is acceptable. Air openings MUST remain unobstructed
with door installed. (For additional installation details, refer to Product
Installation Guide on web.)
• Do NOT install in area exposed to dripping water or outdoor weather
conditions; where gasoline or other flammables are kept or stored; or
where dryer comes in contact with curtains, drapes or anything that
will obstruct flow of combustion and ventilation air.
• For garage installation, dryer MUST be located minimum 18" above floor.
• Floor MUST be solid with 1" maximum slope. Do NOT install on
carpeted surface.
• Dryer MUST exhaust to outside of building, NOT into any concealed
space.
• Exhaust installation requires minimum 4"-diameter rigid or semi-rigid
metal duct with approved, unobstructed vent hood having swing-out
damper(s). If installing rigid metal duct (preferred), do not exceed
MAXIMUM venting run length of 64 ft., allow deductions for elbows
and vents. If installing semi-rigid metal duct, do not exceed MAXIMUM
venting run length of 8 ft., always allow deductions for elbows and
vents. (Refer to Product Installation Guide on web for additional
information.) Do NOT use flexible plastic or metal foil duct and use
shortest run possible.
• Leveling legs supplied to level dryer properly and reduce excessive
noise and vibration.
• For manufactured or mobile home installation optional Mobile Home
Installation Kit (PN # 137067200) required. (For specific installation
details, refer to Product Installation Guide on web.)
Note: For planning purposes only. Refer to Product Installation Guide
on the web at frigidaire.com for detailed instructions.
Optional Accessories
• Mobile Home Installation Kit – (PN # 137067200).
• LP Gas Conversion Kit – (PN # PCK4200).
• Drying Rack – (PN # 137067300).
Top Load Laundry - Gas Dryer
Frigidaire Baseline (P Model)
Recess or Closet Installation
Dryer requires 0" minimum installation clearance
around sides and back of unit. To achieve 0" minimum
rear clearance, dryer MUST be vented straight back.
Closet installation requires additional 1" minimum
clearance between front of unit and vented door. Door
MUST be vented with 120 sq. in. minimum louvered
opening, equally divided, located 3" from top and
bottom of door. A louvered door with equivalent air
openings for full-length of door is acceptable.
Air openings MUST remain unobstructed with door
installed. For additional installation details, refer to
Product Installation Guide on web.
29"
50"
Side
Reversible
Door Swing
Vented door
0" min. 1" min.
Side
60"
sq. in.
min.
3"
60"
sq. in.
min.
3"
0" min. 0" min.
23"
min.
Front
27"
38 1 /
2
"
42 1 /
2
"
Front
120V Power cord
(rear) - 60" long
13 1 /
2
"
3 3 /
4
"
3 3 /
4
"
Gas supply pipe (rear)
Rear vent
1 5 /
8
"