CITIZEN CT-S310II - Manual (Page 43)

— 40 —
Notes: Precautions regarding memory switch settings
*1: MSW2-3
If the spacing expands because print feed stops during printing because transfer of print data is
slow, a white streak may appear at the point that the first point it stops. It is possible to avoid the
white streak by enabling MSW2-3 to improve print quality. However, it will take a little longer for
printing to start.
*2: MSW8-5
If reduce character size horizontally is selected, the print range and distance between lines are
also reduced. When printing on narrow paper, create print data so the print area does not extend
beyond the edge of the paper.
Switch no. Function Initial setting Setting value
MSW7-1 Baud Rate 9600 bps 1200 bps, 2400 bps, 4800 bps, 9600 bps,
19200 bps, 38400 bps, 57600 bps, 115200 bps
MSW7-2 Data Length 8bits 7bits, 8bits
MSW7-3 Stop Bit 1bit 1bit, 2bits
MSW7-4 Parity NONE NONE, EVEN, ODD
MSW7-5 Flow Control DTR/DSR DTR/DSR, XON/XOFF
MSW7-6 DMA Control Valid Invalid, Valid
MSW7-7 VCom Protocol PC Setting PC Setting, DTR/DSR, XON/XOFF
MSW8-1 Print Width 576 dots 360 dots, 384 dots, 420 dots, 512 dots,
576 dots, 390 dots, 546 dots
MSW8-2 Reserved
MSW8-3 Top Margin 11 mm 11 mm, 3 mm, 4 mm, 5 mm, 6 mm, 7 mm,
8 mm, 9 mm, 10 mm
MSW8-4 Line Gap Reduction Invalid Invalid, 3/4, 2/3, 1/2, 1/3, 1/4, 1/5, ALL
*2 MSW8-5 Reduce Char. V/H 100%/100% 100%/100%, 75%/100%, 50%/100%,
100%/75%, 75%/75%, 50%/75%
MSW8-6 Auto Side Shift Invalid Invalid, 1 dot, 2 dots, 3 dots, 4 dots, 5 dots,
6 dots, 7 dots
MSW9-1 Code Page PC 437 PC 437, Katakana, PC 850,858, PC 860,
PC 863, PC 865, PC 852, PC 866, PC 857,
WPC1252, Space, PC 864, Thai Code 18
MSW9-2 Int’Char Set USA USA, France, Germany, England, Denmark,
Sweden, Italy, Spain, Japan, Norway,
Denmark 2, Spain 2, Latin America, Korea,
Croatia, China
MSW9-3 Kanji OFF ON, OFF
MSW9-4 JIS/Shift JIS JIS JIS, Shift JIS (CP932), Shift JIS (X0213)
MSW10-1 Print Density 100 % 70 %, 75 %, 80 %, 85 %, 90 %, 95 %, 100 %,
105 %, 110 %, 115 %, 120 %, 125 %, 130 %,
135 %, 140 %
MSW10-2 Print Speed Level 9 Level 1, Level 2, Level 3, Level 4, Level 5,
Level 6, Level 7, Level 8, Level 9
MSW10-3 Reserved
MSW10-4 Reserved
MSW10-5 Reserved
MSW10-6 Buzzer Event Not by C.Open All Event/Error, Not by C.Open, C.Open/PE