Char-Broil 463741008 - Manual (Page 8)

8 • 463741008
Burner Flame Check
• Remove cooking grates and flame tamers. Light burners, rotate
knobs from HI to LO. You should see a smaller flame in
LO
position than seen on HI. Always check flame prior to each use.
If only low flame is seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.
HI
LO
Turning Grill Off
• Turn all knobs to position. Turn LP cylinder off by turning
hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Press ignitor button rapidly.
"Click" should be heard and spark seen each time between
collector box or burner and electrode. See "Troubleshooting" if
no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valves. Knobs lock in
position. To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to
LO position then turn back to
position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use only
valve/hose/regulator specified by manufacturer.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory
(and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry.
Do not apply a caustic grill/oven cleaner to painted
surfaces.
•
Plastic parts: Wash with warm soapy water and wipe dry.
s
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner.
Use nonabrasive scouring powder
for stubborn stains.
• Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
OFF
OFF
OFF
•Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
CAUTION
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Match-Lighting
s Do not lean over grill while lighting.
1. Turn all burner control valves. Open lid during
lighting. Turn on gas at LP cylinder.
2.
3.
4. To ignite right burner, turn right knob to PRE-HEAT.
Place lit match into match holder, then into side of grill bottom
(as shown below).
Push in and turn IGNITION BURNER knob to PRE-HEAT.
Be sure burner lights and stays lit.
After Lighting: Turn knobs to HI for warm-up.
Ignitor Lighting
s Do not lean over grill while lighting.
1. Turn all burner control valves.
2. Turn on gas source or tank.
3. Open lid during lighting.
4.
5. Push IGNITOR button rapidly.
6.
7.
To ignite, turn IGNITION BURNER knob to PRE-HEAT.
If ignition does NOT occur in 5 seconds, turn the burner
controls , wait 5 minutes and repeat the lighting
procedure.
To ignite right burner, turn right knob to PRE-HEAT.
If ignitor does not work, follow match lighting instructions.
After Lighting: Turn knobs to HI position for warm-up.